ELNA Elnita ec60 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 29

background image

23

REPLACING THE ELECTRONIC COMPONENTS

PRINTED CIRCUIT BOARD A (1)

TO REMOVE:
1.  Remove the front cover (see pages 6 and 7).
2.  Pull out connectors from the printed circuit board A.
3.  Remove the setscrews (6 pcs.) and the printed circuit board A.

TO ATTACH:
4. Follow the above procedures in reverse.

NOTE: Do not disconnect the connectors by pulling on cord.

To disconnect, grasp the connector, not the cord.

Printed circuit board F

connector

Setscrew

Printed circuit board A

Setscrew

Setscrew

Printed circuit board L

connector

«
...
23
24
25
26
27
...
»

Содержание Elnita ec60






























Отзывы:

Нет отзывов

Похожие инструкции для Elnita ec60

INSTANT FOG 1700 PRO

Бренд: Cameo Страницы: 64

Бренд: MAGIC FX Страницы: 20

EXPANDER 750 PROPANO

Бренд: KLINDEX Страницы: 60

Бренд: Jack Страницы: 70

CONTOUR 350 DELUXE

Бренд: H. Winter Страницы: 23

Бренд: MAGMATIC Страницы: 20

Бренд: National Instruments Страницы: 18

Бренд: Singer Страницы: 20

Бренд: Numatic Страницы: 28

HYDRAULIC PANTHER 6280

Бренд: National Страницы: 57

ExSELLerate Series

Бренд: Tornado Страницы: 11

Бренд: Philips Страницы: 54

Бренд: Philips Страницы: 59

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 82

Бренд: Panasonic Страницы: 80

Бренд: Panasonic Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды