Elmes Electronic 04.2015. All rights reserved.
mail:
PROGRAMMING PROCEDURES
1. Learning transmitter(s) to controller's memory
– maximum 112:
a) press control unit
PRG
switch for less than 2 seconds (PRG LED lights on),
b) press transmitter button - LED in controller switches off,
c)
press again the same transmitter’s button – blinking controller LED confirms end of procedure.
2. Programming motor rotation time and PAUSE time:
this procedure can be performed with transmitter learned to controller’s memory or using
wall switch connected to WR input.
a) press control unit PRG switch for more than 2 and less than 8 seconds (PRG LED lights on). Releasing the switch PRG LED sets off,
b) press any hand transmitter button or wired wall switch ( LED lights on) to start motor rotation,
c) after required motor rotation time has lapsed (max. 60 minutes) press the transmitter button or WR switch again - motor stops, courtesy lamp
will switch on,
d) after required PAUSE time has lapsed press transmitter button or WR switch again -
the lamp switches off and the controller’s LED starts
blinking confirming end of the procedure.
3. Deleting all transmitters from control unit memory
(procedure performed when transmitter is stolen or lost)
:
press controller's
PRG
switch (PRG LED lights on) and hold pressed for more than 8 seconds, until the LED starts blinking confirming end of the
procedure. Transmitter memory in the controller is cleared while programmed timings remain unchanged.
Installation:
The control panel should be installed inside protective case to avoid direct exposure to harsh environmental conditions and electric
interference. Connection of wires should be conducted from downwards of the case to avoid possible water flow to the controller board. External
antenna may be connected to the controller by coaxial cable as shown on connection diagram below. Simple wire antenna, as delivered with the
controller, can also be used, however practical operating range of hand transmitters may be reduced.
If photo cells are not used, connection terminals 2 and 3 (counted from the left) must be shorted.
Specification
control panel supply 12VAC with max. 100 mA idle current draw, motor 6,3A fused,
courtesy/warning lamp 40W max., photo cell supply output 12VDC 240mA max., motor oper
ating time 1s…60min.,
regulated overload sensitivity
level 3,5…10A, PAUSE time or lamp ON after motor stops programmable 1…255 seconds,
external dimensions (l/w/h) 140/75/30 mm, operating temperature range: from -20
C to +55
Celsius.
Manufacturer
: ELMES ELECTRONIC, 54-611 Wroclaw
– PL, ul. Avicenny 2, tel. (+48)71-784-59-61, fax (+48)71-784-59-63
Elmes Electronic declares that the product has been manufactured and tested to comply with the following standards:
EN 60950-1 :2001 electric safety, EN 301 489-1 V1.4.1 (2002-08) EMC for radio equipment, EN 301 489-3 V1.2.1 (2002-08) EMC for
Short Range Devices, EN 300 220-3 V1.1.1 (2000-09) EMC and Radio Spectrum Matters.
Manufacturer’s Limited Warranty
Elmes Electronic remote control sets carry one-
year manufacturer’s warranty as from date of purchase. The warranty is limited to the replacement of
faulty original parts or repair defects of improper manufacture. Damage, faulty use or improper handling by the user or installer as well as any chang-
es in product’s hardware or software caused by the user violets the warranty and all due repair costs will be charged. Elmes Electronic shall not be
responsible for any direct or indirect personal or material damage caused by its products failure to operate correctly.
Elmes Electronic reserves the right to change product specification without prior notice.
KEELOQ
®
is a registered trademark of Microchip Technology Inc., USA.
Installation of the controller should be made with power supply OFF and according to schematic diagram below.