manualshive.com logo in svg

ELMED 0141000001, Руководство по эксплуатации

Поделиться
Скачать
ELMED 0141000001 Скачать руководство пользователя страница 8

Page 8

Operation manual ISOTEST 4 S   /   4 S

p l u s

 

4. Technical data

 Power Supply

 

 Supply Voltage

 Lead-acid accumulator, 6 V/4.5 Ah,
with integrated fuse, connecting
cable and two-prong safety plug *
 Lithium battery

 Current consumption (load-
dependent)

 Approx. 0.8 A (2.0 A maximum)

 Test duration (cycle operation)

 Approx. 9 h

 Test duration (continuous
operation)

 2.5 to 5.5 h

 

 

 Test voltage

 

 Magnitude of test
voltage

ISOTEST

ISOTEST

 

4S

: adjustable in 4 steps from

 

10 to 25 kV in steps of 5 kV

 

4S

plus

: adjustable in 7 steps in the 

range of 5 to 35 kV

 Signal shape

 Unipolar high-voltage pulses

 Cycle duration

 Approx. 10 µs

 Pulse repetition frequency

 25 Hz

 Current (rms)

 Approx. 40 mA

 

 

 Dimensions and weights

 

 (complete unit, including carrying
case)

 

 Length

 280 mm

 Height

 230 mm

 Width

 120 mm

 Length of high-voltage cable

 1500 mm

 Weight, including handle

 4.5 kg

 Weight of rechargeable battery

 0.9 kg

 

 

 Type of protection

 IP 42

 Ambient temperature limit:

 -10oC to +50oC
 (Heat timing constant: > 10 K/h)

 

 

* To avoid fire hazards and damage to the rechargeable battery, the
pins of the safety plug must not be shorted under all circumstances.
Even shorting these pins over a short period of time may cause the
fuse to blow and prevent from testing the charge state.
To ensure proper safety and functionality of the rechargeable battery,
defective fuses may only be replaced with original fuses.

Содержание 0141000001













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды