Elkay LZWSRK-EZH2O Скачать руководство пользователя

Страница: 1 / 19

Page 1

1000001734 (Rev. K- 04/18)

EZWSR*1C, *2C LZWSR*1C, *2C

EZWSRK -EZH

ETRO

-F

OTTLE

ILLING

NIT

INSTALLATION & USE MANUAL

EZWSR / LZWSR Bottle Fillers are among the easiest to install on the market today.

To insure you install these models easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK

YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND

OTHER APPLICABLE CODES. After installation, leave these instructions with the

Cooler for future reference.

IMPORTANT

THIS IS AN INDOOR APPLICATION ONLY.

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSON.

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES

IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM

THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN

ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE

WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN

FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE

FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM. WE SUGGEST THAT THE BOTTLE FILLING STATION

AND WATER COOLER BE PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI).

INSTALLER

TOOLS REQUIRED

BUT NOT PROVIDED:

SAFETY GLASSES

GLOVES

3/4” WRENCH OR CRESCENT

WRENCH

5/16” NUT DRIVER

UTILITY KNIFE

TAPE MEASURE

PENCIL

CENTER PUNCH

1/2” SOCKET & RATCHET WRENCH

5/32” ALLEN WRENCH

7/64” ALLEN WRENCH

LZWSRK -EZH

ETRO

-F

OTTLE

ILLING

NIT

Содержание LZWSRK-EZH2O




















Результаты поиска

Содержание LZWSRK-EZH2O

Отзывы:

Похожие инструкции для LZWSRK-EZH2O

Бренды по названию

Популярные бренды

Elkay LZWSRK-EZH2O, Инструкция по установке и использованию

Результаты поиска

Содержание LZWSRK-EZH2O

Отзывы:

Похожие инструкции для LZWSRK-EZH2O

Бренды по названию

Популярные бренды