background image

Elkay Manufacturing Company 

14 

(630) 574-8484 

Built-in Filtered Water Dispenser 

 

1000005232 (Rev. C - 05/19)

5.  Place a container under the water dispenser spout 

to activate the fill sensor and dispense at least one 

gallon of water to bleed off any trapped air from the 

supply lines and filter as well as flush any fine carbon 

particles from the filter.

Note:   The water dispenser is set to automatically shut off 

after 16 ounces of water has been dispensed to 

prevent overflow and potential flooding so multiple 

activations will be required to get the required one 

gallon of water flow through the unit.

6.  If there are no leaks and the unit is functioning 

correctly, install the water dispenser cover and then 

install the filter box cover using the flathead screws 

and a 3/32 inch Allen wrench.

7.  Upon initial startup, the PLASTIC BOTTLES SAVED 

indicator panel should show several bottles have been 

saved due to the water used to initially start up the 

unit.

8.  The left-most FILTER LIFE indicator light should also 

be lit. This light shows the filter is functioning correctly 

and has used less than 65 percent of its capacity.  

 

When the middle blue light illuminates, the filter has 

reached 66 percent of its life and will need to be 

changed soon. When this indicator light comes on, a 

replacement filter should be ordered. 

 

The right-most red light will illuminate in red and 

indicates that the filter should be changed.

FILTER LIFE

PLASTIC BOTTLES SAVED

9.  Once the installation is complete, the water has been 

turned on, and any trapped air has been bled from the 

system re-check for any water leaks.

6. Cleaning

Warm, soapy water can be used to clean the exterior 

panels of the unit. Extra caution should be used to clean 

the glass cover panel. It can be easily scratched and 

should only be cleaned with mild soap and water or glass 

cleaner and a clean, soft cloth. Use of harsh chemicals 

(including bleach), petroleum-based, or abrasive cleaners 

will void the warranty.

Complete care and cleaning instructions can be found at 

http://www.elkay.com/care-and-cleaning

 and click on 

Drinking Water Products Care

For care of the outside surfaces of the water dispenser 

refer to the Elkay website 

http://www.elkay.com/

drinking-products-care

7. Maintenance

7.1  Filter Cartridge Replacement

A filter cartridge is designed to filter approximately 750 

gallons of water at which time it must be replaced. The 

filter should also be replaced every 12 months if the 

750-gallon maximum is not reached.

1.  Remove four screws from filter box cover using a 3/32 

Allen wrench (if filter box is installed).

Содержание ezH2O Liv LBWD00 C Series





















Отзывы: