background image

L669  Rev. A  1/25/2016 

Printed in USA

APPLICATION:

The 

ELK-M1XSLC 

Interface Kit has been enhanced 

to support Lutron's Homeworks and Caséta products.  

Interfacing M1 Control to Lutron allows intelligent control 

of devices in response to security system actions or 

conditions. The most typical integration devices supported 

are:Lights, Shades, and Keypad controllers.  The level 

of integration is dependent on which type and model of 

Lutron devices being implemented.  Some models of 

Thermostats are also supported.  

ELK-M1XSLU SPECIFICATIONS:

 

Connects to the ELK-M1 Keypad Databus

 

Addressable as a TYPE 5 Databus (ID 1-7)

 

Operating Voltage: 12 Volts DC

   Supplied from M1

 

Current Draw: 31mA

 

Activity/Status LED (Orange)

 

Auto-Reset Hardware Watchdog Circuit

 

Housing Dimensions: 4.25" x 6.375" x 2.125"

 

Circuit Board: 2.75" x 3.95"

 

Connects to IP232 via RS232 and null modem (Incl.)

 

Connects to M1 via 4 screw terminals

ELK-IP232 SPECIFICATIONS:

• 

Converts RS232 Serial to IP for connection to the IP

  port on Lutron's QS or Smartbridge Pro Interfaces

• 

LED Indicators for Power, Link, and Data

• 

Operating Voltage: 12 Volts D.C. 

     Supplied from 

ELK-P1216 Power Supply (Incl)

• 

Current Draw: 135 mA

• 

Dimensions: 3.85” L x 1.7” W x 0.93” D

ELK-M1XSLC

M1 Interface kit for Lutron 

Homeworks QS or Caséta Line

HOMEWORKS

®

 QS

INSTRUCTIONS

Specifications are Subject to Change without notice.

NOTICE: Drawings, illustrations, diagrams, part numbers, etc. are provid

-

ed as reference only and are based on equipment available at the time 

the information was created.  All information contained in this document 

are subject to change without notice. 

The extent of integration between Elk Products and Partner Mfgs varies, 

and there may be situations or limitations beyond Elk's control that make 

certain desirable features unavailable or unusable.  Partner products and/

or protocols, including Elk's may not contain the capabilities or data defi

-

nitions to permit additional integration beyond what is currently available.  

Partners may also, at their option, add, modify, or discontinue features or 

support without notification.  

For reasons stated herein, Elk Products makes no warranty that it will 

be able to integrate all available features or operations, nor does it make 

any express or implied warranties of fitness for a particular purpose or of 

merchantability.  Refer to Elk's Limited Warranty. 

 

2017 Elk Products Inc.  All rights reserved.

Lutron, Homeworks, QS, Caséta Wireless, and Smartbridge Pro are 

registered trademarks of Lutron Electronics Co., Inc. 

PO Box 100

3266 US Hwy 70 West

Hildebran, NC  28637

828-397-4200   828-397-4415 Fax

http://www.elkproducts.com

To support integration with Homeworks 

QS, a firmware update to the M1XSLU is 

required.  See page 4 for details.

!

Содержание ELK-M1XSLC















Отзывы: