Elk Products ELK-M1XRF2G Скачать руководство пользователя страница 9

Страница: 9 / 16

M1XRF2G Installation Manual

Page 9

Wireless Setup

Description

Press the right arrow to select Receiver Options.

Rec. Option R03: Reg. Supervision is for "non-fire" transmitters, i.e. transmitters programmed
as "Supervisory Type 1" (see Xmit Transmitter Opt 02 below). The time setting for this
determines how often a sensor must check-in with the control in order to supervise its
presence. The programmable range is 001 to 255 hours. Should a sensor fail to check-in
prior to the expiration of each interval it will be considered "missing". NOTE: A value less than
4 hours is NOT RECOMMENDED! Factory default setting is 024 hours.

Rec. Option R04: Fire Supervision is for "fire" type transmitters, i.e. transmitters programmed
as "Supervisory Type 2" (see Xmit Transmitter Opt 02 below). The time setting for this
determines how often a sensor must check-in with the control to supervise its presence.
Range is 001 to 255 hours. Should a sensor fail to check-in prior to the expiration of each
interval it will be considered "missing". NOTE: A value less than 4 hours is NOT
RECOMMENDED! Factory default setting is 004 hours.

Press the RIGHT arrow key to select 2:Xmit Transmitter Opt.

Use the UP and DOWN arrow keys to locate a particular wireless transmitter. Press the
RIGHT arrow key to select and program the displayed transmitter.

WZnxxx 01 displays whether transmitter xxx is enabled or disabled. It can be used to
temporarily disable an existing enrolled device. It cannot be used to add a new device. This
can only be done via the "learn" or enroll process which then sets this location to a Yes.

WZnxxx 02 is used to select the type of supervision for transmitter xxx. 0 - (No Supervision),
1 - (Regular Supervision), 2 - (Fire Supervision). See receiver selections R02 and R03 for
supervision time values. Factory default setting is 1 (Regular Supervision).

WZnxxx 03 is used to select functionality traits "options" for certain types of GE Transmitter
Devices.

IMPORTANT: Refer to the Listing of GE "Crystal" Transmitters on

previous page for any devices that utilize or require these options.

WZnxxx 04 is used to select functionality traits "options" for certain types of GE Transmitter
Devices.

IMPORTANT: Refer to the Listing of GE "Crystal" Transmitters on

previous page for any devices that utilize or require these options.

WZnxxx 05 is used to set the User ID that will be logged for a transmitter which is a Keyfob
when that Keyfob is used to arm of disarm. Valid range is 001 to 255. Numbers 001 to 199
mirror the keypad user codes. Note: Opening and closing reports may be programmed for
every User code.

WZnxxx 06 is currently NOT required with GE Wireless PIR Motion sensors. It may be used in
the future. * FYI: To conserve battery power almost all Wireless PIR Motion sensors transmit
alarms only, no restorals. Therefore, the panel or receiver must assume a restoral condition
from these sensors after a short time delay. Wireless PIRs also conserve power by only
detecting and transmitting once is a several minute time cycle. They remain quiet until the
time cycle expires, regardless of motion in the room. For this reason Wireless PIRs are not
very practical for most automation or occupancy detection applications.

1234567890123456789012345678901212345

1:Rec Sel

Prg

Receiver Options

1234567890123456789012345678901212345

RO4:=004 Hours

Fire Supervision

From the M1 Installer Level programming locate Menu 14 and press the RIGHT arrow key to
select.

The following four (4) submenus may be selected: 1-Receiver Options, 2-Xmitter Options, 3-
Xmitter Enroll, and 4-Keyfob Event Definitions. Use the UP or DOWN arrow keys to locate the
desired submenu, then press the right arrow key to select.

123456789012345678901234567890121234

1 4 - W i r e l e s s
Setup

†

Not evaluated by UL

123456789012345678901234567890121234