Eljen GSF A42 Скачать руководство пользователя страница 9

Страница: 9 / 56

2018 Indiana Design and Installation Manual

www.eljen.com

2.0 Subsurface Trench and Single Lateral Bed Design and Installation

2.0.4 VERTICAL SEPARATION TO SEASONAL HIGH-WATER TABLE OR LIMITING LAYER:

Refer to section

Rule 410 IAC 6-8.3 70.b.5 for subsurface absorption systems or ISDH Rule 410 6-10.1 (61).

Vertical Separation Distance (VSD)

System Type

Daily Design Flow

Limiting

Layer

Seasonal High

Water Table

Subsurface Trench and Single Lateral
Bed System

>450

30”

24”

<450

24”

Pressure Distribution

Any

24”

VSD measured from the bottom of the excavated trench or bed for the subsurface system.

2.0.5 DISTRIBUTION BOX:

Parallel distribution is preferred. Sequential distribution may be utilized for sloping

sites and must conform to 1.1.4. Distribution boxes are required to be 5 feet from the proximal end of each soil
absorption field trench.

2.0.6 PARALLEL DISTRIBUTION:

Parallel distribution is the preferred method of application to a gravity or pump

to gravity system. It encourages equal flows to each of the lines in the system. It is recommended for most trench
systems.

2.0.7 TRENCH LENGTH:

Trenches will have a maximum of 100 ft in length unless pressure distribution is used per

410 IAC 6-8.3 (74) (r) or ISDH Rule 410 6-10.1 (82) (r).

2.0.8 EQUAL LENGTH:

Trenches must be of equal length in order to provide equal distribution.

2.0.9 SPACING GUIDANCE BETWEEN TRENCHES AND SINGLE LATERAL BED ROWS:

Ensure trenches are

of equal length throughout the system. If using the B43 in a single lateral bed system, ensure there is center to
center distance of 10 feet and 7.5 feet center to center distance for the A42 in a trench.

2.0.10 DISPERSAL AREA:

Dispersal area requirements are located in

IAC 6-8.3 (58) or ISDH Rule 410 6-10.1

(62).

2.0.11 MINIMUM SLOPE REQUIREMENTS:

Maintain a 3:1 slope or gentler for all slopes off the application area.

2.0.12 SUBSURFACE DRAINS:

If subsurface drains are utilized they must remain 10 feet from the edge of the

system sand perimeter.

Содержание GSF A42

























































Результаты поиска

Содержание GSF A42

Отзывы:

Eljen GSF A42, Руководство по установке, Страница: 9 / 56

Результаты поиска

Содержание GSF A42

Отзывы: