Eljen GSF A42 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 56

Eljen GSF A42 Скачать руководство пользователя страница 51

2018 Indiana Design and Installation Manual

51

www.eljen.com

12.0 Inspection/Monitoring Port

The system shall include an Inspection/Monitoring Port designed and installed with access from the ground surface.
It shall be open and slotted at the bottom, and be void of sand or gravel to the infiltrative surface to allow visual
monitoring of standing liquid in the absorption field.  The figures below depict construction and placement of the
Inspection/Monitoring Port.  For beds and elevated systems, place one port per lateral.  At least one inspection port
should be placed at the midpoint of a row.  At the distal ends, use 90-degree elbows and extend to the surface as
an additional inspection port, capped and sealed to be watertight.  One inspection port should be located downslope
in the toe as well.

FIGURE 30: MONITORING WELL FOR SAND-SOIL INTERFACE

TYPAR SOCK

TAPE OR TIE

TO PIPE

PIPE COVER

NON-PERFORATED

4" PIPE

COUPLING

PERFORATED

4" PIPE

OPEN BOTTOM

48"

36"

6"

6"

SPECIFIED SAND

GEOTEXTILE FABRIC

MINIMUM 12"

OF CLEAN FILL

7"

6"

13"

PIPE FLUSH WITH

SAND-SOIL AT

INFILTRATIVE SURFACE

«
...
49
50
51
52
53
...
»

Содержание GSF A42

























































Отзывы:

Нет отзывов