background image

8

Once you have centered the crossbars (B) with the assemblies (A), use the washers (E) and cap nuts (F) to secure the crossbars 

(B) to the upright assemblies (A). Try to make sure the crossbars (B) move as little as possible left to right when securing the  

hardware. 

Do not overtighten.

TORQUE

7-10 FT LBS.

10.5-13.5 NM

To reposition the rack on the t-slot rail, loosen the four cap nuts (F) on each upright assembly (A) to assist in moving the rack. 

Once repositioned, retighten the nuts. 

To adjust the height of the rack remove the center hardware, adjust as needed, then 

replace center hardware.

ADJUSTING AND MOVING THE ELEVATE RACK SYSTEM

Loosen

Loosen

Loosen

Loosen

Center 

hardware

TORQUE

7-10 FT LBS.

10.5-13.5 NM

ELEVATE RACK SYSTEM GUIDELINES

Review all instructions, guidelines, and warranty information before installing or using the Elevate Rack System.

Contact your dealer with any questions regarding proper operations of the Elevate Rack System.

Check state and local laws for compliance with oversized loads.

Adapt speed and care of the vehicle to the load being carried.

Be conscious of load weight, a high center of gravity is a rollover risk. 

All loads change the vehicle’s driving behavior and responsiveness.

Do not use the Elevate Rack System for anything other than its intended purpose.

Do not exceed the maximum load capacity (load capacity does change by terrain).

Do not drive without rack properly installed and fasteners torqued to specification.

Know the overall height of every load. Be vigilant of low clearances.

Remove Elevate Rack System before entering automatic car washes.

Do not use Elevate Rack System if any parts are worn, missing, or broken.

Any questions call 1-877-878-9336

2209 Kellen Gross Dr., Yankton SD 57078 • 877-878-9336

P/N 1118569 Rev. A   Rev. 1-7-22

E

 

F

 

A

 

B

 

F

 

F

 

F

 

F

 

Содержание CS RACK SYSTEMS






Отзывы: