Prior to inspection, assembly and disassembly work,
the system (awning, roller blind) must be switched to a
de-energised state.
All electrical connections, safety devices, fuses, etc. must
be properly installed, connected and earthed.
The power supply provided must be in accordance with
the electric circuit diagram (voltage type, voltage level).
A miniature circuit breaker (MCB) is sufficient to isolate
the system from the power supply (if only one phase and
neutral is used).
If a stationary (permanently installed) drive is not
equipped with a power cable with a plug or another
means of disconnecting it from the mains that has a
contact opening width at each pole according to the
conditions of overvoltage category III (pursuant to
IEC 60664-1) for full disconnection, such a disconnection
device, must be built into the fixed electrical installation in
accordance with facility requirements.
The mains connection cable for drives with a rub-
ber-sheathed cable (abbreviation 60245 IEC 53) can only
be replaced with the same cable type.
The following applies to drives that allow physical access
to unprotected moving parts after installation: Moving
parts of the drive must be fitted more than 2.5 m over the
ground (or another level that offers access to the drive).
4
Product description
The SunTop is an electromechanical tubular motor drive for
window awnings and fabric-based sun protection. During
operation it executes radial movements.
Commissioning the SunTop with
elero
assembly cable for
adjusting the end positions and relief
Blocking recognition (torque limiting)
Parallel switching
• The values for your SunTop that are dependent on the
version can be found on the type plate.
•
The different versions of the SunTop are fitted with dif
-
ferent types of braking systems, depending on the rated
torque and size. This, in turn, can lead to different oper
-
ating behaviour, e.g. with respect to approaching an end
position.
4.1 Product contents
Drive with safety instructions and operating instructions and
any additional components and accessories according to
the order confirmation or delivery note.
4.2 Accessories
Connection and assembly cables, adapter sets, motor bear-
ings, ProLine control units, sensors, radio receivers, bearing
plates, shaft bearings.
5
Assembly
WARNING
Risk of injury due to incorrect assembly
Important safety instructions
►
Observe all assembly instructions. Incorrect assembly
can lead to serious injuries.
CAUTION
Risk of injuries due to hot surfaces.
4 | EN
©
elero
GmbH
Product description
If any risk to persons or operational changes are detect-
ed, the product must be taken out of operation immedi-
ately and the plant operator informed accordingly.
No changes, conversions or attachments may be made
to the product without the permission of the manufacturer.
The system must be frequently checked for improper
balance, signs of wear, and damaged cables and springs
(if applicable).
3.7 Safety notices and directions relating to
transport, assembly and installation
The respective shipping company is responsible for ship-
ping the product. The following safety requirements must
be observed when transporting, assembling and installing
the product:
The product must be secured in line with the require-
ments defined for the transport aid during shipment.
Only lifting gear and lifting tackle that can comfortably re-
sist the forces encountered during loading, unloading and
assembling the product may be used during transport.
Only the designated areas indicated on the pallet and the
product may be used as attachment and lifting points.
During assembly work above head height, use suitable,
inspected and structurally stable climbing aids.
If work must be performed on raised parts or working
equipment, these parts or equipment must be secured
against falling down using suitable devices. Tools used to
lift loads must prevent the loads from unintentionally shift-
ing, freely falling or inadvertently becoming unhooked.
Standing under suspended loads is prohibited.
A safety helmet must be worn during loading work with
lifting gear.
Assembly and installation work may only be performed by
trained and instructed specialist personnel.
The rated torque and rating operating time must be suit-
able for the properties of the driven part (the blind).
On the SunTop type M, the smallest internal tube diame-
ter of the winding shaft is 47 mm; on the SunTop type L,
it is 58 mm.
3.8 Safety instructions relating to operation
The plant operator responsible for the product is obligat-
ed to ensure that it is in safe and proper condition prior to
initial commissioning.
Such checks must also be conducted during operation of
the product at regular intervals determined by the plant
operator.
The SunTop produces mechanical noise when it is op-
erated. The A-rated emission sound pressure level does
not exceed 70 dB(A).
3.9 Safety notices and directions relating to the
electrical installation
All work on the electrical equipment of the system may
only be carried out by authorised electricians according
to the applicable rules and regulations of the trade asso-
ciation, in particular the requirements laid out in DIN VDE
0100. Furthermore, the national legal regulations applica-
ble in the respective country of use must be observed.
In the event of any defects such as loose connections or
defective or damaged cables to the system, the product
must not be put into operation.
