Problem /
malfunction
Possible
cause
Remedy,
correction
• Program-
ming of end
positions not
possible
• Random drive
movements
• The distance
to the end
position or to
the limit stop is
too short
• Delete end
positions
Reset end
positions
• The drive sys-
tem must run,
stop brie
fl
y
and start again
(as long as
a button on
the installa-
tion cable is
pressed).
Fig. 12 RolTop troubleshooting
7 Servicing
The RolTop is maintenance-free.
8 Cleaning
WARNING
Risk of injury due to electricity.
Risk of electric shock.
►
Risk due to potential live parts.
►
Only carry out cleaning when the system is disconnected
from the voltage. To do so, disconnect the drive cable.
►
Clean the product surface only with a soft, clean and dry
cloth.
9 Repair
In case of questions, please contact your local specialist.
Please always provide the following information:
• Article number and designation on name plate
• Type of defect
• Previous and unusual occurrences
• Circumstances
• Own assumption
10 Address
elero
GmbH
Antriebstechnik
Linsenhofer Str. 65
72660 Beuren
Germany
Phone: +49 7025 13-01
Fax:
+49 7025 13-212
[email protected]
www.elero.com
If you require a contact outside of Germany, please visit our
website.
11
Disassembly and disposal
After unpacking the system, dispose of the packaging mate-
rial according to applicable regulations.
After the last use, dispose of the product according to appli-
cable regulations.
Environmental information
No unnecessary packaging material was used. Packaging
can be separated into three material types: Cardboard
(carton), polystyrene (padding) and polyethylene (bag,
protective foam foil).
8 | US+CA
©
elero
GmbH
End position settings | Troubleshooting | Repair
5.6.9 Option D:
Upper end position freely con
fi
gurable,
fi
xed lower end position
Option D: Upper end position freely con
fi
gurable,
fi
xed lower end position
①
In a medium fabric position, using the installation
cable, press the
UP
button
▲
until the fabric has
reached the desired upper end position.
The drive system starts, stops brie
fl
y and starts
again (as long as the button is pressed).
Corrections can be made with the buttons
▲
and
▼
.
②
Keep the
DOWN
button
▼
pressed until the drive
system stops automatically.
The upper end position is set.
③
Press the
DOWN
button
▼
again, until the fabric
has reached the lower end position (to bottom limit
stop).
The drive system starts, stops brie
fl
y and starts
again (as long as the DOWN button
▼
is pressed).
The drive system automatically stops when reaching
the lower limit stop.
④
Keep the
UP
button
▲
pressed until the drive sys-
tem stops automatically.
The lower end position is set.
Optional:
Activation of the relief function for the
lower limit stop: refer to section 5.6.3.
End position setting of option D is completed.
Fig. 11 End position setting option D:
5.7 Technical
data
The separately available „technical data sheet“ will provide
you with an overview of the most important technical para-
meters.
6 Troubleshooting
Problem /
malfunction
Possible
cause
Remedy,
correction
• Drive system
stops during
movement
• End positions
not correctly
set
• Drive system is
in setting mode
• Set end posi-
tions
• Drive system
stops after a
short period of
time
• End positions
have been
saved
• Stiff fabric
• Set second
end position
• Check smooth
running of the
fabric
• Drive system
only runs in
one direction
• Connection
error
• Check connec-
tion
• Drive system
does not react
• No power
supply
• Temperature
limiter has
triggered
• Check power
supply
• Have the drive
system cool
down
