2 | EN
Charging the Lumero-868
The Lumero-868 is delivered in the discharged condition.
Place the Lumero-868 under a lamp for at least 30
minutes or push the DOWN-button on the Lumero-868 for
at least 3 minutes before starting up.
Note:
The travel keys have two levels.
The first level transfers energy from a built-in battery to
the energy store.
The second level activates the travel command.
Programming Lumero-868
Condition
The end positions of the awning, the roller shutter or the
venetian blind have been set, a transmitter has been pro-
grammed, and the Lumero-868 has been loaded (LED
lights and/or flashes wehn a button ist pressed).
For bidirectional use, the device version of the installed
radio receiver is relevant:
elero
Combio form version 75 onwards
elero
RevoLine from version 21 onwards or
elero
radio receiver from manufacturing date May 2012.
1. Move the blind to an intermediate position.
2. Press and hold the
UP
,
DOWN
and
P
buttons on
the programmed hand-held transmitter for at least 3
seconds.
If the blind not travels UP and DOWN, continue at 4.
If the blind does not travel UP and DOWN, continue
at 3.
3. Press an hold the
STOP/P
button on the Lumero-868
for 3 seconds until the transmission LED begins flas-
hing ornage rapidly. The blind now moves UP and
DOWN for 2 minutes. The transmission LED will flash
ornage rapidly every time a button is pressed if the sys-
tem is in programming mode.
4. Press the
UP
button on the unit immediatedly after the
start of an up movement (retract) begins.
The drive will stop briefly.
5. Press the
DOWN
button on the unit immediately after
the start of an down movement (extend) begins.
The drive will stop briefly.
The Lumero-868 ist now programmed.
Possible modes of operation
The Lumero-868 can be operated in four different modes.
The operating mode is indicated by the flashing signal:
1. Awning mode
(1 x flashing of the transmission LED)
2. Visual protection mode
(2 x flashing of the transmission LED)
3. Roller shutter mode
(3 x flashing of the transmission LED)
4. Test mode (checking the light function)
The current mode of the Lumero-868 is displayed by
means of the flashing of the LED.
The awning mode is set as standard in the delivery con-
dition.
In the case of OEM versions, a different mode can also be
set.
Awning mode
The awning is automatically retracted whend the current
measured sun value changes form 1 to 0 (late evening) or
when the current measured light value changes from 0 to
1 (early morning).
Visual protection mode
(protection against prying eyes)
To keep the blind closed even in the evening, close the
blind manually using your hand-held transmitter or a
timer.
The current transitions of the measured light values from
1 to 0 (late in the evening) of from 0 to 1 (early in the
morning) will be ignored.
The blind will remain closed throughout gthe night.
The switching commands such as tilting position (venetian
blind) or ventilation position (roller shutter) will be executed
automatically the next day.
Roller shutter mode
If the roller shutter is driven manually or by a timer of the
lower end position, the light function (driving according to
set light value) will be switched off.
The current transitions of the measured light values from
1 to 0 (late in the evening) of from 0 to 1 (early in the mor-
ning) will bie ignored.
Test mode (checking the light function)
Condition:
The blind is retracted.
The delay times are shortened in the test mode (from
minutes to seconds). You can then test the travel move-
ment of your system when the light threshold is exceeded.
Warning!
Risk of injury by the upward and downward tra-
vel of the awning/venetian blind.
The test mode is active for 5 minutes. This time can-
not be sortened.
Keep away from the operating range of the system.
1. Press the
UP
button for at least 3 seconds until the
transmission LED flashes.
The test mode stays active for 5 minutes but the LED
goes out.
2. Shine a torch (not a LED lamp) on the light sensor.
Specified light threshold value is exceeded.
➙
blind extends/lowers after 5 seconds.
Light value falls below the specified threshold.
➙
upward travel of the awning/blind after 15 seconds.
You can repeat the operation as often as you want within
5 minutes.
© elero GmbH