background image

Program transmitters / program end positions

AstroTec-868

20 | EN 

Programming radio channel settings

Programming transmitter/channel

Prerequisite:  The drive must be installed.

1.  With pre-installed electric receivers, the fuse must be 

 disconnected and reconnected after a few seconds. 
The drive will then remain in programming mode for 
 approximately 5 minutes.

2.  Position yourself in front of the roller shutter/blind with the 

AstroTec-868 in your hand

LR03 (AAA)

Programming button 

P

3.  Press programming button 

P on the back of the device 
briefly. The shutter/blind 
will automatically begin to 
move up and down. This will 
happen for approximately 
2 minutes. 

4.  To define the keyboard layout, press the UP button of the 

AstroTec-868 (located on the front of the device) as soon as the 
shutter/blind begins to move upwards (after approx. 1 second). 

  The shutter/blind will come to a halt briefly. 
   As soon as the shutter/blind begins to move again, press the 

DOWN button on the AstroTec-868.

  The shutter/blind will come to a stop.
  The AstroTec-868 has been successfully programmed.

Note:    Below is the programming/deleting procedure for the 

unidirectional version; the procedure for the bidirectional 
version takes place from page 22

Warnhinweise

Program other AstroTec-868 transmitters

Delete AstroTec-868 transmitters

EN | 21

Deleting individual transmitters
Disconnect the fuse – and reconnect after a few seconds.
1.  Press the following buttons simultaneously:
  • Programming button P (on back of device)
  • STOP button (on front of device)
2.  Keep these two buttons pressed until the LED goes out briefly 

(approx. 3 seconds).

Deleting all transmitters
Disconnect the fuse – and reconnect after a few seconds.
1. Press the following buttons simultaneously:
  • Programming button P (on back of device)
  • UP button 
  • STOP button
  • DOWN button
2. Keep all of these buttons pressed until the LED goes out.

on front of device

}

Programming additional transmitters
To programme additional transmitters in one receiver, please  proceed 
as follows:
1.  Press the UP, DOWN and programming button P on a transmitter 

that has already been programmed in the receiver until the LED 
goes out.

2.   To define the keyboard layout, press the UP button on the hand-

held transmitter as soon as the shutter/blind begins to move 
upwards (after approx. 1 second).

  The shutter/blind will come briefly to a halt. 
   As soon as the shutter/blind begins to move again, press the 

DOWN button on the handheld transmitter. 

  The shutter/blind will come to a stop. 
   The transmitter or this channel has been successfully programmed.

Содержание AstroTec-868 bidi


























Отзывы: