Element 878D, Инструкция по эксплуатации

Страница: 2 / 4

I. APPLICATIONS
1. This unit is suitable for desoldering & soldering operations on a broad range of components. E.g., SOIC, CH-
IP, QFP, PLCC, BGA, SMD, and more. The unit is especially suited for desoldering operations on in-line sock-
ets.
2. You can use this unit for heat shrinking, drying, paint removal, glue removal, defrosting, pre-heating, glue
soldering, and more.
II. CONTROL PANEL
1. Temperature Increase Button (Hot Air Rework Station)
2. Temperature Decrease Button (Hot Air Rework Station)
3. Air Volume Adjustment Knob
4. Cord (Hot Air Gun)
5. Power Switch (Hot Air Rework Station)
6. Receptacle (Soldering Iron)
7. Power Switch (Soldering Station)
8. Temperature Adjustment Knob (Soldering Station)
9. Operation Indicator (Soldering Station)
10. Temperature Display (Hot Air Rework Station)
III. OPERATION
Hot Air Rework Station
1. Set the station appropriately. Install the hot air gun holder onto the left side of the station, and
place the hot air gun in its holder.
2. Install the required nozzle(Use of nozzles in larger diameters is recommended). Connect the st-
ation’s power cord to an electrical outlet.
3. Turn ON the master power switch located at the rear of the station, then turn ON the hot air rewo-
rk station’s power switch. The hot air temperature display will show “---” to indicate the gun in st-
andby mode. Press the temperature increase or decrease button to set the desired temperature.
Pick up the hot air gun, and it will enter standard operation mode, the hot air rework station’s op-
eration indicator light (the dot located at the bottom-right of the hot air temperature display) will
turn ON.
The indicator light will stay ON when the hot air gun is heating up, blink rapidly when the temper-
ature is stabilized, turn OFF when the hot air gun is cooling off. Adjust the air volume adjustment
knob to set the appropriate air volume, and begin operation once the temperature is stabilized.
Once the temperature is stabilized, its status is clearly indicated with a rapidly flashing operation
indicator. The precision PID program is tracking and compensating the hot air gun’s temperature
every millisecond, the hot air gun’s temperature is now in a stable, and precise thermostatic state.
4. The hot air gun must be placed back in the holder when the operation is complete, and turn OFF
the hot air rework station’s power switch. The hot air gun’s operation indicator will turn OFF and
the hot air gun then enters cooling mode. When the hot air gun cools to below 100°C/212°F, the
hot air rework station’s temperature display will turn OFF. If the station is not in use for an exten-
ded period, turn OFF the station’s power switch and DISCONNECT the station’s power cord.
5. Digital Temperature Calibration (Hot Air Rework Station)
Temperature discrepancies may occur due to the change in the environment’s temperature, or the rep-
lacement of the heating element and other components. You can correct the discrepancies with this fu-
nction. The temperature calibration function can improve work efficiency and prolong the lifespan of
the heating element.
2
3
4
7
8
9
10
1
5
6
SPECIFICATIONS
0℃~40℃ / 32℉~104℉
L148*W99*H140mm±5mm
Brushlessblowerwithsmoothairdelivery
≤120L/min
100〜 480℃/212℉ 〜 896℉
200〜 480℃/392℉ 〜 896℉
LED
<2ohms
LEDNixieTube
Mainunitdimensions
Operatingambienttemperature
HotAirReworkStation
AirDelivery
AirVolume
Temperaturerange
Display
SolderingStation
Temperaturerange
Display
Solderingtiptogroundresistance
Indicator for real-time temperature
tracking & compensation