1. Unpacking
Thank you for choosing the
Elektralite Warm White Dazer
fixture. For your own safety, please read this manual before
installing the fixture. This manual covers important information on installation and applications. Please keep this manual for
future reference.
To keep this simple, we are going to refer to the fixture as the
Elektralite Dazer Downlight
throughout the manual.
The
Elektralite Dazer Downlight
fixture uses 36 high powered 5 watt leds in a balanced arrangement giving incredible output.
Please unpack it carefully and check whether it was damaged in shipping.
2. Safety Instructions.
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is
absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. The
Elektralite Dazer Downlight
is a high voltage fixture. Be careful when dealing with high voltages.
Please read this manual. If you do not read this manual and damages occur to the Elektralite Dazer Downlight, then it
could void the warranty.
During shipping,
Elektralite Dazer Downlight
may have been exposed to high temperature changes or humidity changes. So,
as a precaution, do not switch
Elektralite Dazer Downlight
on immediately. Condensation can damage
Elektralite Dazer
Downlight
so leave
it switched off, until it has reached room temperature.
The electric connection must be carry out by a qualified person and it is
absolutely essential that
the
Elektralite Dazer
Downlight
be
grounded
.
This is imperative and is a safety issue.
Always disconnect the
Elektralite Dazer Downlight
from the power source, when the device is not in use or before cleaning it.
Only unplug
Elektralite Dazer Downlight
from the power cord. Never pull out the plug out by pulling on the power cord.
Please keep the
Elektralite Dazer Downlight
away from children and the general public. Please be intelligent and use
common sense when operating the
Elektralite Dazer Downlight
.
3. General Guidelines.
The
Elektralite Dazer Downlight
is a lighting fixture for professional use on stages, in churches, theatres, etc.
The
Elektralite Dazer Downlight
should only be operated at between 120 to 240 volts and only indoors.
The
Elektralite Dazer Downlight
should not be operated 24/7 (24 hours a day; 7 days a week). The
Elektralite Dazer
Downlight
needs operation breaks to ensure that it will work for a long time without problems. Please do not shake the
Elektralite Dazer Downlight
and avoid using brute force when installing or operating it.
When choosing the location to install the
Elektralite Dazer Downlight
, please make sure that it is not exposed to extreme
heat, moisture or dust. The minimum distance between the
Elektralite Dazer Downlight
and the illuminated surface must be
more than 3 feet.
Always mount the
Elektralite Dazer Downlight
with an appropriate safety cable/chain.
Operate the
Elektralite Dazer Downlight
only when you are familiar with the features on the fixture. Do not permit operation
by persons not qualified to operate it.
All modifications to the
Elektralite Dazer Downlight will invalidate the warranty. There are absolutely no exceptions.
If
Elektralite Dazer Downlight
is operated in any way different to the one described in this manual, the
Elektralite Dazer
Downlight
maybe damaged and the guarantee will be void.
4. Changing Lenses.
The
Elektralite Dazer Downlight
comes with a set of different lenses. They are marked in a boxes. When replacing the lens
plate great care has to be taken to not damage the leds themselves. First undo the four screws holding the lens in place and
gently lift the whole lens plate off the leds. Place the new lens plate over the leds making sure the orientation of the lens plate
is correct and the lens plate fits on top of the leds. Use the four screws to attach the plate to the fixture. Take GREAT care not
to screw the screws down tightly as this will crush the leds and possibly damage the leds. Do not use any electrical
screwdriver at any torque setting. Screwing the lens plate down too tightly may not break the leds but could damage the led
terminals so that they will fail at a later date. The screw should be tightened like a car wheel but be no tighter than hand tight
plus a quarter turn. It cannot be said strongly enough to be careful and NOT tighten the screws. Led damage by interchanging
lenses is not covered under warranty in any circumstances. There is also a video on the website showing how to change lens.
