Elekitsorparts FAA-450 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 24

background image

Elekitsorparts Store Item Name: FAA-450_EU1KY_Antenna Analyzer

Item No.: H10010

Document Type: Manual

5

Picture 4: Knocking out the back cover by the rubber handle

Picture 5: Installing the 18650 battery

Also follow the instructions below to activate the battery holder:

1. Insert the battery to the battery holder, pay attention to the Positive and Negative polarity when doing this.
2. Connect the analyzer to your PC with a mini-USB cable (ST-LINK).
3. Slide the switch to CHG to activate the battery holder. When it is in CHG, the ORANGE led will be light. That says the

battery is being charged.

4. To test battery, dis-connect the mini-USB cable and slide the switch to ON, and this will power the analyzer on.

6. Main Screen

The EU1KY FAA-450 analyzer is very different from other antenna analyzers, there is no buttons, switches, tuning pots on the
unit, and all of the operations are through the touch screen When the unit is switched ON, the main screen displays ‘EU1KY

«
...
3
4
5
6
7
...
»

Содержание FAA-450

























Отзывы:

Нет отзывов

Похожие инструкции для FAA-450

Бренд: TaiDoc Страницы: 31

Бренд: Landis+Gyr Страницы: 54

Бренд: Halcyon Страницы: 36

Бренд: Qu-Bit Electronix Страницы: 10

WALLACE & TIERNAN P7 ADVANCED

Бренд: Evoqua Страницы: 98

Бренд: Aktobis Страницы: 7

IMI SENSORS 604B11

Бренд: PCB Piezotronics Страницы: 19

Бренд: Saluki Technology Страницы: 161

Бренд: Eurotron Страницы: 122

Бренд: POSEIDON Страницы: 21

Бренд: Lambda Страницы: 35

Бренд: RaySafe Страницы: 2

Micro Alti Vario Plus

Бренд: Fairhaven Страницы: 20

Бренд: T&D Страницы: 31

Sonic-Pro S6A Series

Бренд: Blue-White industries Страницы: 2

Бренд: FMT Swiss AG Страницы: 24

350 Maritime V2

Бренд: TESTO Страницы: 106

Бренд: Omega Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды