Electrolux SB907SJ05, Руководство пользователя

Страница: 25 / 27

MODELS: SB915SJ*05 SB915WJ*05 FAULT RECALL, OUTPUT TEST
SB925SJ*05 SB925WJ*05 FAULT & OUTPUT INDICATION
Fault Recall and Output Test (SB925)
O
PERATION
I
TEM
I
NPUT
O
UTPUT
Enter Test Mode
Switch dishwasher off by pressing the ‘POWER’
Button
All off
Press & hold ‘PROGRAM’ Button &
‘START/PAUSE’ Button then switch power on.
Keep holding the 2 Button for 2 sec.
‘SENSOR’ LED flashing Display show '1C'
Select F/O Test Press ‘PROGRAM’ Button ‘RINSE’ LED flashing Display shows '2C'
Enter F/O Test Press ‘START/PAUSE’ Button
‘RINSE’ LED on. Display & buzzer showing the last occurred fault (see
‘Fault Indication’ table Page 20)
Press ‘PROGRAM’ Button Display & buzzer showing the 2
nd
last occurred fault
Press ‘PROGRAM’ Button Display & buzzer showing the 3
rd
last occurred fault
Press ‘PROGRAM’ Button
‘FRAGILE’ LED on Display shows ‘4’ buzzer beeps 4 times. Regeneration
valve open (see ‘Output Indication’ table for details Page 20)
Press ‘PROGRAM’ Button Display shows ‘5’ buzzer beeps 5 times. Drain pump on
Press ‘PROGRAM’ Button
Display shows ‘6’ buzzer beeps 6 times. Inlet valve open (only when level
P1 is not detected)
Press ‘PROGRAM’ Button
Display shows ‘7’ buzzer beeps 7 times. Heater on (only when level P1 is
detected)
Press ‘PROGRAM’ Button Display shows ‘8’ buzzer beeps 8 times. Recirculation pump on
Press ‘PROGRAM’ Button
Display shows ‘9’ buzzer beeps 9 times. Detergent dispenser open
(dispenser may open up to 20 sec later)
Press ‘PROGRAM’ Button Display shows ‘10’ buzzer beeps 10 times. Drying Fan on
Press ‘PROGRAM’ Button ‘RINSE’ LED on. Display & buzzer showing the last occurred fault
Press ‘PROGRAM’ Button Repeat
Exit F/O Test Switch off Power Button
Fault Indication (SB915/SB925)
F
AULT
N
AME
D
ISPLAY
C
USTOMER
C
AN
S
EE
S
HORT
E
XPLANATION
W
HAT
H
APPENS
?
No Fault
i 0
--
Not Filling i10 Yes
Pressure switch is not set after 60 secs of
filling
Program stops
Not Draining i20 Yes
Pressure switch is not reset after 120 secs of
draining
Program stops
Flood Control
i30
Yes
Inlet valve fault or 2
nd
pressure switch is set.
Overflow Leak Detection Switch set ( SB925
only)
Program stops
Recirculating Pump
Triac Short Circuit
i50 Yes
Tacho signals are detected while recirculation
pump is not on
Program stops
Not Heating i60 No
Temperature rise <1.5
o
C within 3 min during
heating
Program continues without heating
NTC Fault
i70
No NTC short or open circuit Program continues without heating
EEPROM Fault i80 No
Communication error with external
EEPROM
MCF/CCF Check
Sum Fault
i90 No
Check sum MCF or CCF is not right. Only
detected after switching on.
(Program software not working)
Program selection not possible
Turbidity Sensor
Fault (
SB925 only)
ib0
No
Turbidity signal required for calibration not
reached in 15 sec Program continues with maximum turbidity
response
Tacho Fault id0 No
No tacho signal detected when circular pump
is on Program continues. Circular pump without
speed control. No heating
Filling Time Fault iF0 No Filling timeout Program continues with less water
Output Indication (SB915/SB925)
T
ESTED
A
CTUATOR
D
ISPLAY
B
UZZER
B
EEPS
COMMENT
Regeneration Valve ‘4’ 4 times Not available on these models
Drain Pump '5' 5 times
Inlet Valve ‘6’ 6 times Only when pressure switch is not set
Heater
‘7’
7 times Only when pressure switch is set
Recirculation Pump ‘8’ 8 times
Detergent Dispenser
‘9’
9 times
Drying Fan ‘10’ 10 times
Page 25 DW161