background image

WARNING: ELECTRIC SHOCK COULD OCCUR IF USED ON WET SURFACES.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least

resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord that has an 

equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local codes and ordinances.

WARNING

Improper connection of the equipment-grounding conductor can result in a risk 

of electric shock. Check with a qualifi ed electrician or service person if you are 

in doubt as to whether the outlet is properly grounded. Do not modify the plug 

provided with the appliance—if it will not fi t the outlet, have a proper outlet 

installed by a qualifi ed electrician. This appliance is for use on a nominal 

120-volt circuit and has a ground plug that looks like the plug illustrated in 

(Fig. 09)

 for North American units. For 220/230/240 volt units, consult your local 

building code/electrician. Make sure that the appliance is connected to an outlet 

that has the same confi guration as the plug. No adapter should be used with 

this appliance. Check power unit On/Off switch and all inlet valves for operation. 

This power unit is intended for household and commercial use.

Read all instructions before using this vacuum.

NOTE: Your central vacuum system is listed and approved by the appropriate agencies for dry pick-up only. 

Please see your rating plate for details. To reduce the risk of electric shock, DO NOT USE outdoors or on

wet surfaces.

'2/5.$%$

/54,%4

'2/5.$%$0).

'2/5.$%$

/54,%4

"/8

Fig. 09

12

Содержание Quiet Clean PU3650















Отзывы: