Electrolux EWW1142ADSA, Руководство пользователя, Страница: 17 / 92

16 www.electrolux.com.cn
Time Dry ( ) Touchpad
If you wish to carry out a timed drying
program, keep pressing this touchpad
until the desired time is reached.
Maximum allowable timed drying
changes based on wash program
selected.
The final time value is the total
duration of the w detachment
+ drying cycles.
●
●
At the end of the program the
appliance performs the anti-crease
phase for approximately 10 minutes.
During this time, the display will show
time remaining “ ” and door is
locked “ ”.
●
NOTE
Type of fabric
Load
(kg)
Spin Speed
(rpm)
Suggested
Times (Hrs)
Cotton and linen
(bathrobes, bath towels, etc.).
Dry Time Option Guidelines:
5 - 7
3 - 5
2 - 3 1400
1400
1400 3 - 4
2 - 3
1 - 2
Synthetic or mixed fabric items
( jumpers, blouses, underwear,
household linen, etc.).
Wool and hand washable wool.
3
1 1200
1200 2 - 3
1
1 1200 2
●
●
●
●
The drying time can vary according to :
the final spin speed;
dryness level (Extra Dry or
Cupboard Dry or Iron Dry);
the type of laundry;
the size of load.
Duration of the drying cycle
After drying fluffy fabrics, such as new
towels, it is advisable to perform a Rinse
program to ensure that any residue that
may remain in the tub is completely
removed and does not stick to garments
dried afterwards. After each drying cycle,
clean the drain pump filter. Please refer
to care and cleaning in section 11 “CARE
AND CLEANING”.
Fibre residue
●
●
Additional drying
To prevent the formation of creases
or shrinking of fabrics, avoid
excessive drying.
WARNING!
Should the laundry still be too wet at the
end of the program, set another short
drying cycle.
The final part of a washer- dryer cycle
occurs without heat (cool down cycle).
This ensures the laundry will be left at
a low temperature.
If you wish to open the door
during the anti-crease phase
or interrupt it, press Start/Pause
touchpad.
17
To deactivate the function, press and
hold “Prewash” touchpad about
2 seconds until the display shows the
icon “ ”.
Save Favourite ( ) Program
3.5 Settings
This setting permits you to either enable
or disable the buzzer at the end of the
program. As an example, you might wish
to disable this buzzer when you start a
wash when going to bed, so that when the
wash finished approximately 1 hour later,
it will not disturb you through the night.
Enabling/Disabling End-Of-Wash
Buzzer
Program settings that are frequently
used can be saved (e.g. Cotton, 60°C,
1200 rpm, with Prewash and Vapour).
To program/re-program Favourite with
your own selections and save them,
proceed as follows:
1. Put machine in Stand-By mode.
2. Select your desired program settings.
Child Safety Lock ( ) Option
Your appliance is provided with CHILD
SAFETY LOCK which permits you to
leave the appliance unsupervised with
the door closed without having to worry
that children might be injured by or cause
damage to the appliance.
Set this option after pressing the
Start/Pause touchpad.
To activate the function, press and
hold “Prewash” touchpad about
2 seconds until the display shows the
icon “ ”.
To set “Child Lock” option:
This function remains enabled
even after the appliance is
switched off.
The touchpads are locked
(except for the On/Off button).
●
●
If you press any touchpad while
Child Lock is activated, the icon
“ ” will flash on display
3 times along with buzzer sound.
3.6 Start/Pause ( ) and
Add Clothes ( ) Touchpad
Error warning beeps such as critical
faults are not disabled.
This touchpad has 2 functions:
To disable the buzzer sound, press
“SensorWash ( )” and “Vapour ( )”
touchpads at the same time about
3 seconds, the icon “ ” will show
on display along with buzzer sound.
To return to default configuration
press these 2 touchpads at the same
time about 3 seconds, the icon “ ”
will show on display along with buzzer
sound.
●
●
Start/Pause ( ) 1.
If you have selected a “Delay Start”
option, the countdown will begin and
will be shown on the display.
After you have selected the desired
program and options, press this
touchpad to start the machine. The
Start/Pause pilot light will stop flashing
and remain lit until the water level is
above the bottom edge of the door
then pilot light goes OFF.
To recall the favourite wash program,
turn selector knob to “Favourite ”
program. You will get acknowledgement
on the screen when the Favourite
program is loaded.
3. To save favourite program, press and
hold “Vapour ” touchpad about
2 seconds and you will hear “Bip, Bip”
sound and “Favourite” LED is flashing.