Electrolux ETB4600B, Руководство пользователя

Страница: 15 / 36

CONCERN WHAT TO DO
Refrigerator is too warm
Ensure food is allowed to cool before placing inside the refrigerator.
Ensure the appliance is set up as per instructions on page 11.
Ensure that contents are not obstructing the cooling vents.
Ensure the door is not held open or is being opened too frequently.
Freezer is too warm
Adjust temperature to a colder setting.
Ensure food is allowed to cool before placing inside the freezer.
Ensure the appliance is set up as per instructions on page 11.
Ensure that contents are not obstructing the cooling vents.
Ensure the door is not held open or is being opened too frequently.
Food is freezing in the refrigerator Adjust temperature to a warmer setting.
Ensure that fruit and vegetables are stored in the crisper. Items with a high water
content should not be placed near the cooling vents.
Unable to change temperature settings Refer to function guide in Controlling Your Refirgerator.
Ensure that user interface is in “awake” mode before trying to adjust temperature
settings.
Appliance noise
Your new refrigerator may make sounds that your old one didn’t make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard surfaces, like the floor, walls and cabinets, can make the
sounds seem louder than they actually are. The following describes the kinds of sounds and what may be making them.
CONCERN WHAT TO DO
Motor noise
(compressor)
Nothing. This is normal as your new refrigerator uses a high-speed compressor
which switches on and off during operation.
Note that the compressor noise may seem louder at the start of the on cycle.
A clicking noise heard just before
the compressor starts.
Nothing. This is normal as your new refrigerator has an automatic switching action
of the temperature control, turning the compressor on and off.
Occasional gurgling, similar
to water boiling.
Nothing. As each cycle ends, you may hear a gurgling sound due to the
refrigerant flowing in your refrigerator system.
Airflow noise. Nothing, this is normal as your new refrigerator uses high efficiency fans to circulate air.
Rattling and
other noises.
Ensure that the cabinet is level and stable, refer to
Installation Instructions on page 6.
Check the surrounds of the appliance to ensure there is nothing
touching or placed on top of the appliance.
Ensure that contents of the appliance are not placed in such a way
that they are vibrating (such as bottles).
Crisper Operation
CONCERN WHAT TO DO
Excess moisture build up in crisper
It is normal for there to be some moisture
and humidity in the crisper bin.
Ensure that the crisper is not over packed.
Crisper bin can not be removed If crisper bin interferes with the door bins, remove door bins before removing
crisper.
Position cabinet so that the door can be fully opened.
Freezing items in the crisper Adjust temperature to a warmer setting.
Refrigerator operation
CONCERN WHAT TO DO
Appliance will not run
It is normal for the freezer fan not to
operate during the automatic defrost cycle,
or for a short time after the appliance is
switched on.
Ensure that the cord is plugged into a live power outlet and outlet is switched on.
Ensure that the household circuit breaker has not tripped or that the fuse has not
blown.
The appliance maybe in defrost mode, check again in half an hour.
Compressor motor seems to run too long
At normal room temperatures, expect your
motor to run about 40% to 80% of the time.
Under warmer conditions, expect it to run
even more often.
Ensure that the doors are not held open
Check that large amounts of warm food have not just been placed inside the
appliance.
Note that the appliance will run more than normal just after you install it or when
adjusting to temperature setting changes.
The exterior of the appliance is warm or hot
to touch
This is normal because the appliance
transfers heat from the inside out through
the outer panels and the divider between
the doors.
Ensure the appliance has the external clearances recommended in the section
“Installing your new appliance”.
The exterior of the cabinet will be much warmer on warmer days it may even feel
hot to touch, as the appliance is working harder.
User interface will not respond
To ensure settings are not accidentally
changed the user interface will go into
sleep mode when not in use. Press any
button to wake user interface
Check that the user interface is in awake mode, refer to section “About the user
interface”.
Check that the user interface is not locked, refer to section “About the user
interface”.
If the user interface is frozen turn the appliance off for five minutes for the memory to
clear, then turn back on.
Check that the user interface is not in Sabbath Mode, refer to control instructions.
(I&W models only).
Alarms Sounding
Check that all doors are fully closed.
Ensure that the over temperature alarm is not being activated by hot food placed in
the freezer.
Check if the drinks timer has ended, refer control instructions.
Check if the Filter Replacement alert is activated, refer control instructions.
(I&W models only)
Frost build up Check that all doors are fully closed.
Ensure that the doors are not opened too often.
Ensure that the return air vents are not blocked with packaging.
Ensure the seals are clean and not obstructed.
Odours The interior may need cleaning, refer to cleaning guide.
Ensure that food is stored correctly as some food, containers and wrapping can
produce odours.
Check appliance for old or unusual food.
Lights not working
The LED lighting is designed to dim
automatically if the door is left opened
for more than 5 minutes and turn off
completely if the door is open for more
than 7 minutes. Closing the door will reset
the timer.
The LED lighting is also designed to turn
on gradually.
Ensure that the cord is plugged into a live power outlet and outlet is switched on.
Ensure that the household circuit breaker has not tripped or that the fuse has not
blown.
Check that the user interface is not in Sabbath Mode, refer to control instructions.
Check the appliance features section to determine lighting configuration for your
model. Check that the doors are closed completely
English 1 5