Electrolux EMC4090X Скачать руководство пользователя

Страница: 33 / 43

SOI 12.06 FV

33/43

599 37 42-75

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE

CONTROL PANEL ASSEMBLY REMOVAL

1. CARRY OUT 3D CHECKS.
2. Disconnect the main wire harness from the
control

panel.

3. Remove the one (1) screw holding the control
panel to the oven cavity.

4. Lift the control panel assembly and pull it
forward. Now, the control panel assembly is free.

FAN MOTOR REPLACEMENT

REMOVAL

1. CARRY OUT 3D CHECKS.
2. Remove the one (1) screw holding the noise filter

to the chassis support.

3. Release the noise filter from the tabs of the fan
duct.
4. Remove the three (3) screw holding the chassis

support to the oven cavity front flange, back plate,

and the magnetron.

5.   Remove the chassis support from the oven
cavity.
6.   Disconnect the wire leads from the fan duct.
7.   Remove the one (1) screw holding the fan duct to
the

back

plate.

8. Release the tabs of the fan duct from back plate.
9. Remove the fan duct from the oven.
10. Remove the fan blade from the fan motor shaft

according to the following procedure.

1) Hold the edge of the rotor of the fan motor by

using a pair of groove joint pliers.

CAUTION:

• Make sure that no swarf from the rotor enters

the gap between the rotor & stator of the fan

motor.

• Avoid touch the coil of the fan motor with

the pliers as the coil may become cut or

damaged.

• Avoid deforming the bracket whilst using the

pliers.

2) Remove the fan blade assembly from the shaft

of the fan motor by pulling and rotating the fan

blade with your hand.

3) Now, the fan blade is free.

CAUTION:

• Do not re-use the removed fan blade as

the fixing hole may be oversize.

11. Remove the two (2) screws holding the fan motor

to the fan duct.

12. Now, the fan motor is free.

INSTALLATION

1. Install the the fan motor to the fan duct with the

two (2) screws and nuts.

2. Install the fan blade to the fan motor shaft

according to the following procedure.

1) Hold the centre of the bracket which

supports the shaft of the fan motor on a flat

table.

2) Apply the screw lock tight into the hole (for

shaft) of the fan blade.

3) Install the fan blade to the shaft of fan motor

by pushing the fan blade with a small, light

weight, ball peen hammer or rubber mallet.

CAUTION:

• Do not hit the fan blade when installing

because the bracket may be deformed.

• Make sure that the fan blade rotates

smoothly

after

installation.

• Make sure that the axis of the shaft is

not

slanted.

3. Insert the tabs of the fan duct to the back plate.
4. Install the fan duct to the back plate with the one
(1)

screw.

5. Re-install the chassis support to the oven cavity

with the four (4) screws.

6. Install the noise filter to the fan duct and the

chassis support with the one (1) screw.

7. Re-connect the wire leads to the fan motor.

Groove joint

Coil

Stator

Gap

Bracket

Rotor

Rear view

Shaft

Table

Center of
bracket

Shaf

Axis

Stator

Rotor

These are the position
that should be pinched
with pliers

Side view

Содержание EMC4090X












































Результаты поиска

Содержание EMC4090X

Отзывы:

Похожие инструкции для EMC4090X

Бренды по названию

Популярные бренды

Electrolux EMC4090X, Руководство по обслуживанию

Результаты поиска

Содержание EMC4090X

Отзывы:

Похожие инструкции для EMC4090X

Бренды по названию

Популярные бренды