14
19
USE OF THE ELECTRIC GRILL
1
– NATURAL CONVECTION OVENS
The oven is fitted with:
• a lower heating element;
• an upper heating element.
It is possible to select the desired temperature into the oven by
turning clockwise the thermostat knob and depending on the
models, one or more functions:
Oven off
Oven light
60
÷
max Upper + lower heating element on
Upper heating element on
Lower heating element on
Grill element on ( turnspit optional )
2
– MULTIFUNCTIONAL OVEN
The oven is fitted with:
• a lower heating element;
• an upper heating element;
• a circular heating element surrounding the fan.
N.B.: Always set the temperature on the thermostat knob before
selecting any of the functions.
Oven thermostat knob
To obtain an oven temperature between 60
°
C and MAX
°
C (or 0 - 11),
turn the knob clockwise.
Oven commutator knob
Depending on the type of oven, it is possible to select one of the
following functions turning the commutator knob clockwise.
.
WARNING - GRILL:
Always use the grill with oven door half-open (at the first hinge
release), and with knobs protection installed, as per the specific
instructions provided in the grill use.
GAS ADJUSTMENT
2
1
3
4
5
L
N
A
1
60
2
80
3
100
4
120
5
140
6
155
7
175
8
190
9
210
10
230
11
250
The appliance is foreseen to operate the grill with half-open door
(fig. 2) and with the grid on the third shelf from the oven bottom,
at about 12 cm from the surface, and with the deflector placed as
in (fig. 2). The user can change the shelves, depending on his
personal whishes and on the different food.
Geat the oven 5 minutes before introducing the food.
Note:
All the functions mentioned above switch the oven internal light on. A
warning light on the control panel will stay lit until the temperature is
reached; after it will light up intermittently. Always use the oven with the
oven door closed
m
a
x
6
0
9
0
13
0
17
0
200
Temp.in
°
C
Use of the oven
Note: ovens with separate thermostat and commutator.
When the functions are used, place the thermostat knob
between 180
÷
200
°
C as maximum temperature.
1
2
3
4
5
6
7
1
0
11
9
8
6
0
8
0
10
0
12
5
150
17
5
2
0
0
2
2
5
m
ax
Pos.knob
IMPORTANT
The wires in the mains lead are coloured in accordance with the
following code:
GREEN AND YELLOW......EARTH
BLUE .................................NEUTRAL
BROWN .............................LIVE
REPLACEMENT OF THE CABLE
In case the cable is damaged, replace it in accordance with the
following instructions:
- open the box of the supply board as described on the picture
below;
- unscrew screw “A” fixing the cable;
- replace the cable with one of the same lenght and in accordance
with the features described on the table; switch the appliance
off, and close the gas tap
- the ‘green-yellow” earth wire must be connected to the terminal
“ “ and it must be about 10 mm longer thean the live wires;
- the “blue” neutral wire must be connected to the terminal marked
with letter “N”;
- the live wire must be connected to the terminal marked with letter
“L”.
Conversion to LPG
Always isolate the cooker from the electricity supply, turn off the
gas supply temporarily and proceed as follows.
- change the injectors,
- adjust the minimum flow of the burners.
REPLACEMENT OF WORK-TOP INJECTORS
In order to change the work-top injectors, it is necessary to act as
follows: remove the grids, remove burners and flame-spreaders
(see fig.A), change the injector (see fig.B) and replace it with
another one suitable for the new type of gas (see table D). Re-
assemble everything in the opposite direction, paying attention to
place the flame-spreader in the right way on the burner.
A
B
Fig. 11
MINIMUM FLOW ADJUSTMENT FOR WORK-TOP TAPS
In order to adjust the minimum, act as follows: switch the burner
on, and turn the knob towards the minimum flow position
.
Remove the knob from the tap, introduce a little screwdriver in the
tap rod (fig. 11).
Attention: in taps with security valve, the minimum adjusting screw
“Z” is placed outside the rod tap (fig. 12).
WARNINGS
Isolate the cooker from the electricity supply before attempting to
replace the oven lamp.
The oven lamp used is of a special type withstanding high
temperatures. To replace it, act as follows: disassemble the
protecting glass (A) and replace the burnt lamp with one of the
same type. Reassemble the protecting glass.
DISASSEMBLE OF WORK-TOP
In case it is necessary to repair or replace the inside components,
act as follows:remove the glass lid from its position slipping off it
upwards.
Remove the grids, remove burners and flame-spreaders (see
fig. 13), unscrew the visible screws “V” placed on the work-top
(see fig. 14). Disassemble the work-top by unscrewing the 4 rear
screws “A” (see fig. 15 ).
Unscrew the adjusting screw in order to increase the flow or screw
it to decrease the flow.
The right adjustment is obtained when the flame has a length of
about 3 or 4 mm.
For butane/propane gas, the adjusting screw must be tight screwed.
Make sure that the flame does not go out passing quickly from
the max. flow
to the minimum flow .
Assemble the knob again.
APPLIANCE MAINTENANCE
Fig. 12
Z
TAB. D
GENERAL INJECTORS TABLE
Kind of gas
mbar Nozzle
Burners
Power Watt
Consum.
N.
type
max.
min.
max.
115
-Rapide
3000
750
286 l/h
NATURAL
20
97
-Semi rapide
1750
480
167 l/h
72
-Auxiliary
1000
330
95 l/h
128
-Triple crown
3300
1300
298 l/h
120
- Fish
2900
1500
262 l/h
G.P.L.
30
85
-Rapide
3000
750
219 g/h
BUTANE
28
65
-Semi rapide
1750
480
128 g/h
PROPANE
37
50
-Auxiliary
1000
330
73 g/h
93
-Triple crown
3300
1300
241 g/h
85
- Fish
2900
1500
211 g/h
GB
ATTENTION:
The temperature shown on the control panel corresponds to the
temperature in the oven centre only when the functions selected
are or
.
When you turn the control knob to this position, the light will be
on for all the following operations.
Defrosting with fan
The air at ambient temperature is distributed inside the oven for
defrosting food very quickly and without proteins adulterations.
The thermostat knob must be placed on the maximum position.
Natural convection
Both the lower and upper heating elements operate together.
This is the traditional cooking, very good for roasting joints, ideal
for biscuits, baked apples and crisping food.
You obtain very good results when cooking on a shelf adjusting
the temperature between 60 and MAX
°
C.
Fan oven
Both the fan and the circular heating element operate together.
The hot air adjustable between 60 and MAX
°
C is evenly distributed
inside the oven. This is ideal for cooking several types of food
(meat, fish) at the same time without affecting taste and smell.
It is indicated for delicate pastries.
Medium grill
It is indicated for grilling and gratinating small quantities of traditional
food.
The thermostat knob must be placed on the maximum position.
Total grill
It is indicated for grilling and gratinating traditional food.
Turn the thermostat control knob to the 200
°
C position.
Fan assisted total grill
The air which is heated by the grill heating element is circulated
by the fan which distributes the heat on the food.
The fan assisted grill replaces perfectly the turnspit. You can obtain
very good results also with large quantities of poultry, sausage,
red meat. Turn the thermostat control knob to the 200
°
C position.
Air forced lower heating element
The air which is heated by the lower heating element is circulated
by the fan which distributes the heat on the food.
This function can be used to sterilize food. This function can be
used between 60 and MAX
°
C
GB
E 14
25 W - 230 V~
T300
°
C
A
Содержание EKM90355X
Страница 1: ......