Operation
2-8
16.7 msec.
H : GND
L : -5V
LSI
The I/O signal of the LSI is detailed in the following table.
Pin No.
Signal
I/O
Description
1-2
VL2-VL1
IN
Power source voltage input terminal.
Standard voltage for LCD.
3-5
AN7-AN5
IN
Terminal to change cooking input according to the Model.
By using the A/D converter contained in the LSI, DC voltage in accordance with the
Model in operation is applied to set up its cooking constant.
6
AN4
IN
Temperature measurement input: MAGNETRON THERMISTOR.
By inputting DC voltage corresponding to thetemperature detected by the thermistor,
this input is converted into temperature by the A/D converter built into the SLI.
7
AN3
OUT
Back light circuit (Light emitting diodes) driving signal.
8
AN2
IN
To input signal which communicates the door open/close information to LSI.
Door close “H”level signal (0V). Door open “L”level signal (-5V).
9
AN1
IN
Humidity sensor input f
This input is an analog input terminal from the humidity sensor circuit, and connected
to the A/D converter built into the LSI.
10 AN0
IN
Used for initial balancing of the bridge circuit (humidity sensor). This input is an analog
input terminal from the humidity sensor circuit, and connected to the A/D converter
built into the LSI
11
P57
OUT
Oven lamp, fan motor stirrer motor and inverter unit driving signal
To turn on and off shut off relay (RY 1). The
square waveform voltage is delivered to the
RY1 driving circuit.
12
P56
OUT
Signal to sound buzzer (2.0 kHz).
A: key touch sound.
B: Completion sound.
13 P50
OUT
Terminal not used.
14-18 P54-P50 OUT Used for initial balancing of the bridge circuit (humidity sensor)
19
P47
OUT
Power level data output signal for inverter unit.
The power level will be decided by the time ratio
of T1 and T2.
20
P46
IN
Signal coming from touch key.
When either G1 line on key matrix is touched, a corresponding signal out of P20 - P27
will be input into P46. When no key is touched, the signal is held at “H”level.
21
P45
IN
Signal similar to P46.
When either G2 line on key matrix is touched, a corresponding signal will be input into
P45.
22
P44
IN
Signal similar to P46.
When either G3 line on key matrix is touched, a corresponding signal will be input into
P44.
23
P43
IN
Signal similar to P46.
When either G4 line on key matrix is touched, a corresponding signal will be input into
P43.
24
INT0
IN
Signal synchronized with commercial power source frequency.
This is the basic timing for time processing of LSI.
A
B
0.1 sec.
2.0 sec.
H : GND
L : -5V
H : GND
L : -5V
16.7 msec.
During cooking
H : GND
L : -5V
16.7 msec.
T1
T2
L : -5V
H : GND
Description of LSI
Содержание EI30MH55GBA
