Electrolux EDW 1100, Руководство по обслуживанию

Страница: 50 / 56

9.1.1. Overview Errors Displayed
ERROR Entry in the text line of the display
Acoustic
display
Number of signal
tones
Short description Was passiert?
2Hz / 5sek. pause
if activated
--- Clear rinse missing PLEASE CLOSE DOOR --- ---
--- Klarspüler fehlt REFILL RINSE AID --- ---
--- Salt missing REFILL SALT --- ---
--- Filter soiled* CLEAN FILTER --- ---
Errors are always displayed at the end of the program if the internal counter has
reached 20. After the next program start, the counter will be set to 0.
i10
Tap closed OPEN THE TAP ERROR CODE i10 1 mal
Only has validity for program steps with filling to level: the forward break-over point of the
pressure control device is not reached after 60 sec. at the latest.
The following has validity for each 1st static filling of a program part: after
Timeout 90 Sec. > 45 Sec. Pump out > error message
The program is halted and can be continued after remedying the error by activating the Progr.
button. However, should the error not be remedied and the progr. button is activated, the
dishwasher continues until the next part program drying.
i20
Drain pump DRAIN BLOCKED ERROR CODE i20 2 mal
Switch-back point of the pressure control device is not reached
after max. 120 sec.. Program is halted.
The program is halted and can be continued after remedying the error by activating the
Program button
i30
Aqua-Control SERVICE CODE i30 ERROR CODE i30 3 mal Aqua-Control System directly deactivates the valve. The program is halted and continues automatically after the error has been terminated.
i50
Circulating pump
Triac short circuit
SERVICE CODE i50 ERROR CODE i50 5 mal Tacho pulses are recognised although the U-Pump has not been triggered.
The program is terminated and water runs in until the forward break-over point of the
pressure control device is reached.
i60
Heating element --- ERROR CODE i60 ---
No temperature increase of min. 1.5K was detected within a period of 3 min. during the
heating phase.
Program continues until the end without the heating function!
i70
NTC-sensor --- ERROR CODE i70 --- NTC short circuit or interruption. Program continues until the end without the heating function!
i80
EEPROM --- ERROR CODE i80 --- Communication error with the ext. EEPROM
i90
Check sum
MCF / CCF
--- ERROR CODE i90 ---
Check sum (variants programming) MCF or check sum CCF is incorrect.
Is only recognised after activation!
No program selection possible.
ON/OFF-LED on
iA0
Rinsing arm
blocked
SPRAYARM BLOCKED ERROR CODE iA0 Dauerton
The rotation of the rinsing arm is checked and evaluated at the start of the program
and at the start of each of the program steps, in addition to after open/close door and a
power failure..
Error output until the rotational speed of the rotating arm is detected or no triggering
takes place.
iB0
Turpidity sensor --- ERROR CODE iB0 ---
The opaqueness signal which is required for calibration is not achieved within a period
of 15 sec.
Opaqueness is always detected.
The program process is adapted accordingly.
iC0
Communications
error
--- ERROR CODE iC0 ---
The communication with the user interface is subjected to interference. The dishwasher halts and waits until the communication is restored.
iD0
Tacho --- ERROR CODE iD0 ---
With a triggered circulating pump, no tacho pulse is detected for 5 + 20 sec..
Circulating pump without control, heating switched off.
This function is then rechecked in every step.
iF0
Filling time error --- ERROR CODE iF0 --- The time limits is exceeded during filling
Program runs into the next part prog. without level.
Subsequent clocking for the repeated obtaining of water is not applicable.
Errors are reset after a complete pumping out.
Text display
customer
Text display
Servicemode / cust. service