manualshive.com logo in svg

Electrolux Built-In Dishwasher, Руководство по обслуживанию

Поделиться
Скачать
Electrolux Built-In Dishwasher Скачать руководство пользователя страница 8

8

5995432258

To change the

Icemaker  Controls

All parts of this appliance capable of conducting
electrical current are grounded. If grounding
wires, screws, straps, clips, nuts or washers
used to complete a path to ground are removed
for service, they must be returned to their
original position and properly fastened.

CAUTION

To avoid personal injury when servicing the
condensing unit, stand on a ladder which will
give enough support to allow removal of the top
panel and safely allow access to service the unit.

REFRIGERATION DIAGNOSIS

ELECTRICAL SPECIFICATIONS

Max Defrost Control
w/No Door Openings........................16 hrs
Evap Defrost Thermistor........68°F (FZ)..63°F (FF)
Electrical Rating: 115V AC 60 HZ.............5.4 amp
Maximum Current Leakage......................0.75 mA
Maximum Ground Path Resistance...............0.1 W
Energy Consumption Model 42........50.5 KWh/mo
Energy Consumption Model 48......53.75 KWh/mo

COMPOENENT RESISTANCE VALUES

FF fan motor ……………………..............1600 &! ± 20%
FZ fan motor ………………………….......1600 &! ± 20%
Condenser fan motor ………………........1600 &! ± 20%
Auger motor ………………………..............3.7 &! ± 15%
Cube motor …………………………….....2091 &! ± 10%
Cover motor ……………………………....2091 &! ± 10%
Defrost heater FZ ……..................................44 &! ± 7%
Drain heater FZ ..........................................377 &! ± 7%
Sub-heater FZ ………...............................1322 &! ± 7%
Defrost heater FF .......................................120 &! ± 7%
Drain heater FF …......................................440 &! ± 7%
Fill-tube heater .……….............................2645 &! ± 7%
Dispenser heater (Recess)………………..1889 &! ± 7%
Compressor (between the different
phase) …………….....................11. 7 &! ± 7% / 1 phase
3- way valve …………………………..40 ± 4 &!/ 1 phase
Water valve (Ice maker) …………...............180 &! ± 7%
Water valve (Dispenser) ..………................325 &! ± 7%

Technical Data

Nomenclature

TECHNICAL DATA

IMPORTANT SAFETY NOTICE

This information is intended for use by individuals
possessing adequate backgrounds of electrical,
electronic and mechanical experience. Any
attempt to repair a major appliance may result
in personal injury and property damage. The
manufacturer or seller cannot be responsible for
the interpretation of this information, nor can it
assume any liability in connection with its use.

NO LOAD PERFORMANCE

Control Position 37-0°F and
Ambient Temperature of: 

70°F 90°F

Fresh Food °F 37-42 36-43
Frozen Food °F (-2)-2 (-2)-5
Percent Running Time, %..........35-45 65-75

REFRIGERATION DIAGNOSIS

To access the 

low pressure 

side of the system,

install a line tap

 

valve on the process tube

extending from the compressor case.

REFRIGERATION SYSTEM

Refrigerant Charge (R134a)......................8.11 ounces
Compressor......................................738-1270 BTU/hr
Minimum Compressor Capacity
Vacuum..........................................................26 inches
Minimum Equalized Pressure
@70°F.............................................................66 PSIG
@90°F.............................................................74 PSIG

Содержание Built-In Dishwasher


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды