manualshive.com logo in svg

Electrolux Built-In Dishwasher, Руководство по обслуживанию

Поделиться
Скачать
Electrolux Built-In Dishwasher Скачать руководство пользователя страница 52

52

5995432258

Fresh Food Evaporator Components

To access the fresh food evaporator components:

1. Access the fresh food evaporator assembly.
   (

See Fresh Food Evaporator Assembly.

)

2. Remove the fresh food evaporator fan  assembly. (See

    Fresh Food Evaporator Fan Assembly.

)

3. Access the fresh food evaporator. (See 

Fresh Food

   Evaporator.

)

Defrost Safety Thermostat

To remove the defrost safety thermostat, remove the
single Phillips-head screw from the thermostat mounting
bracket. Separate the defrost thermostat from the bracket.

Fresh Food Evaporator Thermistor

To remove the fresh food evaporator thermistor,
pull it straight out from its mounting tube.

Note: 

The defrost heater is not available separately and

only comes as a part of the evaporator assembly.

Replacing the Freezer or Fresh Food
Evaporator

The freezer evaporator can be replaced as a complete unit,
including the defrost components and fan assembly, or it
can be replaced as an individual component.

The fresh food evaporator can be replaced as a complete
unit or as an assembly consisting of the evaporator and
defrost heater (the fresh food defrost heater is not
available separately).

To replace the freezer or fresh food evaporator:

1. Access the specifi c evaporator as described in 

Fresh

    Food Evaporator Assembly 

or 

Freezer

    Evaporator Assembly

.

2. In the machine compartment, remove the screws that
    hold the main switch in place. Move the main switch
    out of the way to provide better access to the
    evaporator tubing.

3. Remove the condenser fan assembly from the
   compartment. (See 

Fans

.)

4. Remove the 5 Phillips-head screws holding the metal
   cover over the Styrofoam block (see photo below).
   Remove the metal cover.
5. Remove the Styrofoam block from the base of the
   evaporator tubing.

Note: 

Adhesive may be holding the Styrofoam block in

place after the metal cover is removed.

Содержание Built-In Dishwasher


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды