Electrolux Professional 371000, Быстрое руководство

Страница: 15 / 20

15
The green indicator “A“ signals that the corresponding hot-
plate is on.
The yellow indicator “G“ signals that the heating elements are
on.
The electric control knob “B“ of each hot-plate has the following
positions (see Fig. 5):
0: “Off“
1...5: “Medium power with energy positions range
between 1 and 5“
6: “Maximum power“
The selector knob “D“ has following symbols (see Fig. 6):
“Off“
“Appliance On“
“Upper and lower heating elements“
“Upper heating elements“
“Lower heating elements“
The adjusting knob “E“ has following symbols (see Fig. 6.
100: “Minimum temperature“
120.-
..28-
0: “Medium temperature with energy positions range
between 120 and 180“
300: “Maximum temperature“
For detailed information about the appliances’s over-
view see the complete Installation and User manual on
the web site.
G COOKTOP USE
G.1 Gas models — Lightning on
Cooktop
SeeFig. 1
1. Press and turn knob “H“ to position .
2. Press the knob down fully and hold a flame to the pilot in
order to light.
Hold the knob down for about 20 seconds; when released,
the pilot flame must remain lit. If it does not, repeat the
operation.
3. To light the main burner, turn the knob from position to
position.
4. For the minimum flame, turn the knob from position to
position.
Cooktop with igniter without pilot flame
SeeFig. 2
1. Press and turn knob “H“ to position . Press the knob
down and at the same time press igniter button “L“. Hold
the knob down for about 10 seconds; when released, the
flame must remain lit. If not, check for residual moisture on
the ignition plugs, dry if necessary and repeat the
operation. If the problem occurs again, use a lighter
2. For the minimum flame, turn the knob from to .
Oven
SeeFig. 3
1. Press knob “I“ lightly and at the same time turn it
anticlockwise a few degrees to release it.
2. Press down fully and turn it to position .
A click will indicate sparking.
3. Keeping knob “I“ pressed, turn it to position.
4. Hold it there for about 15/20 seconds to allow the gas to
reach the pilot burner and the thermocouple to heat.
5. Use knob “L“ to select the required temperature.
Fan oven
SeeFig. 4
NOTE!
Press button “P“ to activate the fan oven.
1. Press knob “I“ lightly and at the same time turn it
anticlockwise a few degrees to release it.
2. Press down fully and turn it to position .
A click will indicate sparking.
3. Keeping knob “I“ pressed, turn it to position.
4. Hold it there for about 15/20 seconds to allow the gas to
reach the pilot burner and the thermocouple to heat.
5. Use knob “L“ to select the required temperature.
For detailed information about the gas appliances’s
lightning on see the complete Installation and User
manual on the web site.
G.2 Electrical models — Lightning on
Cooktop
SeeFig. 5.
1. Turn on the main switch located ahead of the appliance.
2. Turn control knob “B“ of the required hot-plate, to one of
the six available positions marked on the control panel,
bearing in mind that “1“ corresponds to minimum power
and “6“ corresponds to maximum power; Lighting up of
green indicator “A“ signals that the corresponding hot-
plate is on
3. To adjust hot-plate heat, turn the knobs firstly to “6“; on
reaching maximum cooking or boiling temperature, turn
the knob to a lower setting.
Oven
SeeFig. 6
1. Turn heating element control knob “D“ to the required
setting.
2. Lighting up of green indicator “A“ signals that the power is
on.
3. Turn thermostat knob “E“ to the required cooking temper-
ature (between 100 ℃ and 300 ℃ ).
4. Lighting up of yellow indicator “G“ signals that the heating
elements are on; it goes off when the oven reaches the set
temperature.
For detailed information about the electrical applian-
ces’s lightning on see the complete Installation and
User manual on the web site.
G.3 Gas models — Switching off
Cooktop
SeeFig. 1
1. Turn knob “H“ from or position to position;
2. To shut off the pilot, press the knob lightly and turn it to
position.
Cooktop with igniter without pilot flame
SeeFig. 2
1. Turn knob “H“ from or to position ;
O
1