background image

ELECTRO-VOICE

®

 

 Xi-A Rigging Manual

1

Table of Contents

0. Rigging-Safety Warning .......................................................................................................................................... 2

I. Introduction

......................................................................................................................................................... 3

1.1 The Flying Xi-A Loudspeaker Systems .................................................................................................... 3

II. Basic Xi-A Rigging Primer ....................................................................................................................................... 3

2.1 Anatomy of an Xi-A Flying System ........................................................................................................... 3

2.2 The Rigging Hardware ............................................................................................................................. 4

2.3 The Xi-A Flying Concept .......................................................................................................................... 7

2.3.1 Accoustical Considerations ...................................................................................................... 7

2.3.2 Practical Considerations .......................................................................................................... 8

III. Associated Rigging Hardware for Flying Xi-A Loudspeaker Systems .................................................................. 10

3.1 Grids and Associated Rigging Hardware ............................................................................................... 10

IV. Strength Ratings, Safety Factors, and Special Safety Considerations ................................................................. 10

4.1 Strength Ratings and Safety Factors ..................................................................................................... 10

4.2 Special Safety Considerations for Xi-A Loudspeaker Arrays .................................................................. 12

4.3 Special Safety Considerations for Rigging Strap Assemblies ................................................................. 14

4.3.1 Redundant Attachment Points ................................................................................................ 14

4.3.2 Special Considerations for Polyester Webbing ....................................................................... 14

4.4 Special Safety Considerations for Grid & Building Structural Supports .................................................. 14

V. Rigging Inspection and Precautions ..................................................................................................................... 15

5.1 Xi-A System Components ...................................................................................................................... 15

5.1.1 Xi-A Loudspeaker Systems .................................................................................................... 15

5.1.2 Rigging Strap Assemblies ...................................................................................................... 15

5.2 Associated Hardware ............................................................................................................................. 15

5.2.1 Grid Assembly ........................................................................................................................ 15

5.2.2 Chain Hoists ........................................................................................................................... 15

5.2.3 Building Structural Supports ................................................................................................... 15

5.2.4 Mechanical Components ........................................................................................................ 16

VI. Appendices ....................................................................................................................................................... 17

Appendix A Xi-A Rigging Accessories ........................................................................................................ 17

Appendix B References ............................................................................................................................. 17

B.1 Accoustical References ............................................................................................................ 17

B.2 Mechanical References ............................................................................................................ 18

Содержание Sound Reinforcement System Xi-1123A/106F





















Отзывы: