ELECTRO FREEZE Arctic Swirl
®
Model HDM75A-----1
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
14
184984
6.6 Motor Brush Replacement
6.4 Belt Replacement
6.5 Motor Replacement
1.
Repeat steps 1 through 6 of the
Spindle Shaft Replacement, para.
6-1.
2.
Remove old belt and install new
belt (7).
3.
Slide motor (30) to the rear and
adjust proper belt tension of 5/16
inch. (See para. 5-2, Pulley
Alignment and Belt Tension.)
4.
Reverse the above steps to
reassemble.
1.
Repeat steps 1 through 6 of the
Spindle Shaft Replacement,
paragraph 6-1.
2.
Loosen the two set screws holding
the motor pulley (8) in place. Apply
heat to the hub, remove the pulley
and set aside.
3.
Disconnect motor leads from the
speed control. Note the terminal
locations for reassembly of new
motor. Remove green ground wire
on support (45).
4.
Remove three screws (10) holding
the air flow control panel (47) and
remove panel.
5.
Remove the four mounting screws
(22) on the rear panel of the
machine holding the motor
weldment support assembly (6)
and support legs (45) in place.
Remove motor (30) and motor
support (6, 45) as an assembly
from the blender base assembly
(24). Move the assembly to a work
bench and remove the old motor.
5.
Install the new motor (30) with the
four mounting screws (10) and
washers (11,12).
6.
Reverse the above steps to
reassemble. Refer to Wiring
Diagram, Section 9, to connect
wires. (You
MUST
reapply Loctite
RC/680 adhesive to the shaft and
pulley according to the
manufacturer’s
recommendations.)
7.
Check rotation of motor after fully
assembled. Rotation is CCW
(counterclockwise) when viewed
from the top.
1.
Repeat steps 1 through 5 of the
Spindle Shaft Replacement, para.
6-1.
2.
Use a screwdriver to remove two
caps (black plastic, near bottom of
motor) holding the carbon
brushes. Replace the brushes
and end caps.
3.
Reverse the above steps to
reassemble.
