ELECTRO FREEZE Arctic Swirl
®
Model HDM75A-----1
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
4
184984
3.1
Selector Switch
3. The bottom position, “JOG”, is
momentary run. Power is supplied to the
drive motor and the spindle shaft will
spin as long as the switch is held in this
position. This is a spring-loaded position.
“ON” is the machine’s normal operating
position.
This three-position toggle switch has a
center “OFF” position with top and
bottom power positions. (See figure 1
for location of controls.)
1. The top position, “ON”, is
continuous run. Power is provided to
the drive motor continually and the
spindle shaft will spin. DO NOT ALLOW
MIXER TO OPERATE AT HIGH
SPEED UNDER NO LOAD, OR AT
LOW SPEED UNDER LOAD.
2. “OFF” is the center position.
Power is provided to the switch only.
The drive motor will not run. If any work
is to be done within the cabinet, THE
POWER CORD MUST BE DISCON-
NECTED FROM THE WALL OUTLET.
3.2
Speed Control
This control adjusts the speed of the
drive motor and spindle shaft. The
machine is normally operated at a
specific setting for the desired product.
A lower speed is normally used when
washing or rinsing the shaft with water.
The lower speed helps prevent the water
from splashing out of the cup. As a
reference point for spindle shaft speed,
remember that when the control dial is at
zero (0), the spindle shaft should be
turning slowly.
3
Control Panel Identification and Operating
Instructions
