background image

 

IMPORTANT SAFETY INFORMATION 

Please  read  this  user  manual  before  using  this  heater  and  keep  it  safe  for  future 
reference. 

 

Read the following instructions carefully and be sure your patio heater is properly 
installed, assembled and cared for. Retain the instructions for future reference.   

 

Failure to follow these instructions may result in serious bodily injury and/or 
property damage.     

 

WARNING - Risk of Suffocation!

 

Gas heaters must be used outdoors and must 

not be used in enclosed areas such as sheds or marquees!     

 

Read the instruction manual before using the appliance.     

 

WARNING: Accessible parts may be very hot. Keep young children away.   

 

This appliance must be kept away from flammable materials during use.     

 

Do not move the appliance during use.     

 

The appliance should be secured to the ground when in use. 

 

Turn off the gas supply at the gas cylinder after use.     

 

Do not modify this appliance.     

 

If you have any questions concerning assembly or operation, consult the retailer 
or Bottled Gas Company.     

 

Always place the appliance and cylinder on flat level ground.     

 

Turn off the gas cylinder if gas leak is suspected.   

 

Parts sealed by the manufacturer must not be altered by the user. No 
modifications should be made to any part of this heater and repairs and 
maintenance should only be carried out by a registered Gas Safe service 
engineer.   

 

Use only regulator and hose approved for LP Gas at the correct pressures and 
gas type.   

 

The regulator should comply with the standard EN16129 and current regulations 
in the country where it is installed, which may be found at your nearest retailer of 
gas items.   

 

Refer to the technical data. It is strictly prohibited to use adjustable pressure.   

 

The life expectancy of the regulator is estimated as 10 years. It is recommended 
that the regulator is changed within 10 years of the date of manufacture or the 
national conditions require it. 

 

The type of replaceable hose should be compliant with EN16436-1. 

 

The hose used must conform to the relevant standard for the country of use. The 
length of the hose must be 0.7 meters (minimum) and 1.5 meters (maximum). A 
worn or damaged hose must be replaced. Ensure that the hose is not obstructed 
or kinked. It is recommended that the hose is changed within 1 year of the date of 
manufacture or as the national conditions require. 

Содержание EQODHMBL















Отзывы: