Duplicating Multi Channel
Transmiter RT31
1. Connect both Multi Channel Transmitters
with the programming cable.
2. On the target transmitter
keep the 0 button pressed
until the duplication symbol
flashes in the display and
hold than the middle Enter-
button pressed. The symbol
in the display is shown
continuously.
3. Within 10 seconds press the button of the
source transmitter briefly and then the
middle ENTER-button. You can release
the ENTER- button of the target
transmitter now.
The display shows the
duplicating process on both
Multi Channel Transmitters.
4. As soon as the duplication
process is completed the
symbol on the right flashes
on the display.
5. Remove the programming cable.
Random Coding
1. Insert the
programming
cable into the
socket on the
Multi Channel
Transmitter,
and short-
circuit one of
the outer pins
with the middle
pin.
The connection of the pins must be kept
until the random coding process is
completed.
2. Keep the button 1 pressed
until the random coding
symbol flashes in the display.
3. Press the middle ENTER-
button. The symbol is shown
continuously.
4. Within 10 seconds type in
the channel number for
which the random code is
supposed to be memorized.
Then hold down the middle
ENTER-button. The display
shows the process.
As soon as the process is
completed the symbol on the
right flashes on the display.
Release the ENTER button.
5. Remove the programming cable.
6. Transfer the new coding to the radio
receiver! For this also see the operating
instructions of the radio receiver.
Replacing the Battery
1. Unscrew the bottom of the housing.
2. Remove the old battery.
3. Insert a new 3 V battery. Use only
batteries of type Cr2032.
Make sure the polarity is correct!
4. Screw the bottom of the housing back on.
Caution!
Keep batteries out of the reach of
children!
Cleaning
-
Carefully wipe the housing with a damp lint
free cloth.
-
Do not use solvent-based cleaning agents.
These can damage your health and
destroy the surface of the housing.
Disposal
Customer Service
Put the packaging material into the
recycling bins for cardboard, paper
and plastics.
Waste electrical products may not be dis-
posed of with household waste!
Warranty
If, despite correct handling, faults or
malfunctions occur or if the product was
damaged, please contact the company at the
address below:
ELDAT GmbH
Im Gewerbepark 14
D-15711 Königs Wusterhausen
Deutschland
Telefon: + 49 (0) 33 75 / 90 37-310
Telefax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-Mail:
Conformity
Dispose of the waste product via a
collection point for electronic scrap or
via your specialist dealer.
Dispose of used batteries in a recy-
cling bin for batteries or via the spe-
cialist trade.
This product conforms to the basic
requirements of the R&TTE Directive
1999/5/EC.
Within the statutory warranty period we
undertake to rectify free of charge by repair or
replacement any product defects arising from
material or production faults.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty
null and void.
The Declaration of Conformity can be found
on the Internet at: www.eldat.de.
-
The display only lights up faintly:
Change the batteries.
-
The display does not light up at all:
Check the polarity of the batteries.
-
If the receiver still does not react:
Move closer to the radio receiver or
memorize the Multi Channel Transmitter
channels in the radio receiver again.
Trouble Shooting
88494 0309 GB
General Information
1
2
3
5
7
9
E N T E R
6
8
0
4
A new code can be programmed for each
channel button of the Multi Channel
Transmitter.
OK
Cancel