background image

8

E

n

g

li

s

h

14.Lift the lid and remove the sample paper. The sample paper may be kept in

one of the resealable bags for further chemical analysis.

15.When all samples have been taken, switch the instrument off by pressing

the red pushbutton twice in quick succession.

16.Close the lid and ensure that the magnetic catch is fully engaged.

4.3 Taking samples using smaller sample papers

If the standard 110 mm diameter High Purity Sample Papers are too large for
the area to be sampled, half size, quarter size or 22 mm wide strip papers can
be used as follows. Care must be taken to ensure that sample papers do not
become contaminated.

1. Put on a pair of clean disposable gloves.

2. Using  tweezers,  remove  an  Elcometer  130  SCM400  High  Purity  Sample

Paper from the pack.

3. Fold paper as follows:-

For half size paper fold standard paper in half and cut into two along fold
line. 

For  quarter  size  paper  fold  standard  paper  into  quarters  and  cut  into
quadrants along fold lines.

For  22 mm wide  strip  fold standard  paper  into  half and  cut 11 mm  either
side of fold line.

4. Fill a 2 ml syringe with an appropriate amount of high purity water:-

For a half size paper use 0.8 ml

For a quarter size paper use 0.4 ml

For a 22 mm wide strip use 0.4 ml

5. Holding sample paper in tweezers, eject the correct amount of water onto

its surface. Take care to retain as much water as possible on the paper.

6. Follow Steps 5 to 10 (inclusive) in Section 4.2.

7. Using the central marker on the inner electrode to aid positioning, place the

sample  paper  over  the  concentric  electrodes  as  appropriate,  ensuring  all
entrapped air is removed:

Содержание SCM400























Отзывы: