manualshive.com logo in svg

Elation PLATINUM SPOT 15R PRO, Руководство пользователя

Поделиться
Скачать
Elation PLATINUM SPOT 15R PRO Скачать руководство пользователя страница 20

 
 

 

Platinum Spot 5R Pro™

 

 

©Elation Professional, Los Angeles, Ca                  20 

       www.ElationLighting.com

 

 

Be sure to follow the above figure when making your own cables. Do not use the ground lug 

on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or 

allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the 

shield could cause a short circuit and erratic behavior. 

 

 

 

DMX-512 control connection 

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the 

other side to the male 3-pin XLR input of the moving head (Please refer to the diagram 

below.). You can chain multiple moving heads together through serial linking. The cable that 

should be used is two conductor, shielded DMX cable with XLR input and output connectors. 

Always be sure daisy chain your in and out data connections, never split or “Y” your DMX 

connections unless you are using an approved DMX splitter such as the Elation Opto 

Branch 4™ or DMX Branch/4™.   

 

 

Содержание PLATINUM SPOT 15R PRO





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды