Operating Modes:
You can use the ELED Fresnel in two ways:
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512
controller such as
as the Elation® Show Designer™.
Master-Slave Operation:
This function will allows you to link units together to run in a Master-
Slave mode. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units built-in programs.
Any unit can act as a Master or as a Slave
however, only one unit can be
programmed to act as the “Master.”
Master-Slave Connections and Settings:
1
. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR microphone cables to link your units together.
Remember that the Male XLR connector is the input and the Female
XLR connector is the ouput. The first unit in the chain (master) will
use the female XLR connector only. The last unit in the chain will use
the male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. For the “Slave” unit(s), press the MODE button until “XXX3” is dis-
played.
4. Use the UP and DOWN buttons to adjust the address. The slave unit
must be set to the same address as the Master unit.
5. Connect the “Slave” unit or units and they will automatically start to
follow the “Master.”
Manual Dimmer:
1. Plug the fixture in and press the MODE button until “XXX4” is dis-
played.
2. Use the UP and DOWN buttons to adjust the LED intensity.
This onboard control mode is regulated by the max and minimun
intenstiy settings. These settings are set in the DIM MAX SETTING
and DIM MIN SETTING onboard control modes.
Dim Max Setting:
The Dim Max Setting will set the maximum dimness level for manual
control and DMX mode.
1. Plug the fixture in and press the MODE button until “XXX5” is dis-
played.
ELED Fresnel Operating Instructions
Elation Professional - www.elationlighting.com - ELED Fresnel Instruction Manual Page 8
Elation Professional - www.elationlighting.com - ELED Fresnel Instruction Manual Page 7
2. Use the UP and DOWN buttons to adjust the maximum value of the
LED dimmer. The setting can be adjusted between 50-100%.
Dim Min Setting:
The Dim Min Setting will set the minimum dimness level for manual con-
trol and DMX mode.
1. Plug the fixture in and press the MODE button until “XXX6” is dis-
played.
2. Use the UP and DOWN buttons to adjust the minimum value of the
LED dimmer. The setting can be adjusted between 0-30%.
DMX Mode:
Operating through a DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. This function
also allows you to use your fixtures as spot lights.
The ELED Fresnel has
2 DMX modes: 1 Channel mode and 2 Channel mode. See page 9 for
each modes’ DMX traits.
Remember the maximum and minimum dim-
ness levels are set in the Dim Max & Dim Min Settting menus.
1. This function will allow you to control each individual fixture’s traits
with a standard DMX 512 controller such as the
Elation® Show
Designer™ or the Elation® DMX Operator™.
2. To run your fixture in DMX mode, plug in the fixture via the XLR con-
nections to any standard DMX controller. Select your desired DMX
mode, and then press the UP or DOWN buttons to adjust the DMX
address.
XXX = DMX Address
3. To run the 1 Channel Mode, press the MODE button until “XXX1”
is displayed. This is the DMX addressing for the 1 Channel Mode.
4. To run the 2 Channel Mode, press the MODE button until “XXX2”
is displayed. This is the DMX addressing for the 2 Channel Mode.
3. Please see pages 10-12 for DMX values and traits
ELED Fresnel Operating Instructions
