manualshive.com logo in svg

Elastic Networks ELMo 120, Руководство по установке и обслуживанию

Установка и регулярное обслуживание Эластичных сетей ELMo 120 - это ключевые шаги для эффективной работы продукта. Скачайте бесплатное Руководство по установке и обслуживанию с нашего сайта manualshive.com, чтобы получить подробные инструкции по уходу за вашим устройством.

Поделиться
Скачать
background image

ELMo 120 Multiplexer installation and testing   2-19

Revision 2.01

ELMo 120 Multiplexer Installation and Maintenance Guide  

08-01023-01

Installing ELMo 120 Multiplexer connections for voice/data service (continued)

7

Connect the two split connectors of a second ELMo 120 cable harness to the 
"Line CPE" connectors of the same two filter cards connected in step 5. See 
Figure 2-12.

Figure 2-12
Line/CPE connections on the filter shelf

8

Connect the Amp-Champ connector of the "Line CPE" cable harness to the 
Amp-Champ connector originating from the "Line CPE" connection on the 
EtherLoop cross-connect.

Figure 2-13
ELMo 120 Multiplexer intermediate Voice Networkconnection

—continued—

J1

J2

1

(Filter shelf connectors 6-10 not shown)

2

3

4

5

Line CPE

Connectors

ELMo 120 cable harness from J1/J2 
"Line CPE" filter shelf connectors 

Intermediate cable from "Line CPE" 
connection on the cross-connect

Содержание ELMo 120









































































Отзывы:

Нет отзывов

Похожие инструкции для ELMo 120

Ryobi RP4020 User Manual preview
RP4020
Бренд: Ryobi Страницы: 223
Hioki DT4261 Remote Operation Manual preview
DT4261
Бренд: Hioki Страницы: 11
Kane KANE505 Instruction Manual preview
KANE505
Бренд: Kane Страницы: 24
RLH Industries RLH-PM-3 Series User Manual preview
RLH-PM-3 Series
Бренд: RLH Industries Страницы: 14
GW Instek GDM-8261 Quick Start Manual preview
GDM-8261
Бренд: GW Instek Страницы: 14
Craftsman 81079 Owner'S Manual preview
81079
Бренд: Craftsman Страницы: 26
PacketLight Networks PL-1000RO 3.3 Installation And Configuration Manual preview
PL-1000RO 3.3
Бренд: PacketLight Networks Страницы: 211
United Electronic Industries DN-MUX-414 Series User Manual preview
DN-MUX-414 Series
Бренд: United Electronic Industries Страницы: 32
UNI-T UT60A Operating Manual preview
UT60A
Бренд: UNI-T Страницы: 44
VOLTCRAFT VC-20 Operating Instructions Manual preview
VC-20
Бренд: VOLTCRAFT Страницы: 106
Duratool D03124 Manual preview
D03124
Бренд: Duratool Страницы: 10
Pacific Micro Systems DM1210N Operation Manual preview
DM1210N
Бренд: Pacific Micro Systems Страницы: 11
CEN-TECH 32418 Operating Instructions Manual preview
32418
Бренд: CEN-TECH Страницы: 12
Sanwa PC5000a Instruction Manual preview
PC5000a
Бренд: Sanwa Страницы: 45
East Coast Datacom Nx8- Dual Composite MUX High-Speed 16-Port TDM Multiplexer Operation Manual preview
Nx8- Dual Composite MUX High-Speed 16-Port TDM Multiplexer
Бренд: East Coast Datacom Страницы: 77
Triplett 1101-B Instruction Manual preview
1101-B
Бренд: Triplett Страницы: 2
Triplett 614395002251 User Manual preview
614395002251
Бренд: Triplett Страницы: 22
Shortridge Instruments Airdata ADM-870 Operating Instructions Manual preview
Airdata ADM-870
Бренд: Shortridge Instruments Страницы: 56

Бренды по названию

Популярные бренды

Загрузить еще бренды