background image

 

 

Application manual 

 

Presence / movement sensors EK-DF2/DG2-TP  

 

Rev. 1.2 - 2020-02-06 

 

MAEKDF2DG2TP_EN 

© Ekinex S.p.A. 

– All rights reserved 

 

Pag. 14 

Parameter name 

Conditions 

Values [Default] 

If enabled, each channel can also be controlled from the KNX bus through communication objects #5-6-
7-8. 

For Light control channels, the CO (which is of 1-bit Switch type) also controls the dimming function. 

This pushbutton is required to switch those channels On for which semi-auto mode is selected. 

Lux / Time / 

Sensitivity(Meter)/ 

STBY selected by 

Device type = Master

 

ETS 

IR 

Selects the source for the main device parameters: Brightness threshold, activation delay, sensitivity, 
standby delay. If the source is "ETS", the IR remote has no effect on these parameters. 

This setting is only relevant for the two Light Control channels (C1-C2). 

Test mode 

Device type = Master

 

Disable 

Enable 

If enabled, starts the test mode at the end of the download. Test mode automatically exits to normal 
operation after 10 min. or upon command from the IR remote. 

Sensor sensitivity 

 

Maximum 

High 

Medium 

Low 

OFF 

Used to increase or decrease the sensitivity of the 

PIR according to user’s requirement. 

This setting is available both for master and slave configurations. 

LED turns on when PIR is 
triggered 

 

Disable 

Enable 

When enabled, the red LED will turn on for 1 s every time movement is detected. This indication can be 
suppressed; however, all other indication functions of the LED remain enabled. 

 

13.3  Menus: Light control output C1 / C2 

Following parameters are repeated for each of the two Light Control channels C1 and C2

Although not specified below, these options are only listed if the corresponding channels are active. 

Parameter name 

Conditions 

Values [Default] 

Auto / Semi-auto select 

Device type = Master

 

Auto 

Semi-auto 

The automatic mode controls both switch-on and switch-off; the semi-automatic mode only controls 
switch-off after a manual switch-on through the external control pushbutton. 

Output type 

Device type = Master

 

Switching 

Dimming 

Switching mode is used to control an On/Off actuator through a Switch-type object; in this mode, Standby 
function and Constant light control are not available. 

Dimming mode controls a dimming-capable actuator through an Absolute dimming object (for the 
Standby function) and a Relative dimming object (for Constant light control). 

Dimming value during ON 
phase 

Device type = Master 

Output type = Dimming

 

1...100% 

[100%]

 

Содержание EK-DF2-TP























Отзывы: