Eisen HT3300, Инструкция по эксплуатации, Страница: 2 / 6

2
SAFETY INFORMATION
• Follow workshop health & safety rules,
regulations and conditions when using the
floor jack .
• This is a lifting device only. Do not use it for
anything other than its intended purpose.
Load must be supported by proper rated
capacity ja ck stands under the vehicle before
starting inspection or work. Do not overload.
Jack capacity is 3 tons.
• Use only on hard level surfaces.
• Never stand or place your body beneath the
load being lifted.
• Never attempt to exceed the limits of the
floor jack. Applying excessive force to the tool
can over load the ja ck, decrease the life and
increase the wear on the ja ck.
• Lift only on areas of the vehicle as speci fi ed by
the vehicle manufacturer.
• Do not move or dolly the vehicle while it is on
the j ack.
• Use genuine parts only. Unauthorized parts
may be dangerous and will void the warranty.
• K eep the floor jack clean and in good working
order for best and safest performance.
• DO NOT use the fl oor ja ck for a task it is not
designed to perform.
• DO NOT use for aircraft purposes.
• DO NOT overreach. Keep proper footing and
balance at all times. Do not reach over or
across the product.
• DO NOT drop, throw or abuse the fl oor ja ck.
• Failure to heed these markings may result
in serious person al inj ury and/or property
damage.
WARNING!
• DO NOT use the fl oor ja ck if damaged or
thought to be faulty. Contact your local service
agent.
PACKAGING CONTENT
DESCRIPTION QTY.
Floor Jack
1
Lower Handle 1
Upper Handle 1
O.I.P.M.
1
TOOLS NEEDED
• 10 mm spanner / 3/8” spanner
• 18 mm spanner / 11/16” spanner
• 8mm hex key/ 5/16” hex key
BEFORE INSTALLATION
• Make sure all equipment is rated to the
appropriate capacity.
• Check damaged parts. Before using the tool,
any part that appears damaged should be
carefully checked to determine that it will
operate properly and perform its intended
function. Check for alignment and binding of
moving parts, any broken parts or mounting
fixtu res; and any other condition that may
damaged should be properly repaired or
replaced by a qua lifi ed technician.
• Always use good quality hydra ulic jack oil
when adding or replacing the oil in your
together. Whe n filli ng the Floor Jack with oil,
do not permit dirt or any other substance to
enter the hydraulic system. (Refer Maintenance
of Page 3 for more details.)
• Make sure that all connections are secure.
• Consult the vehicle owner’s manual to
determine the location of lift points.
WARNING!
• Defective accessories can lead to personal
injury a nd material damage
INSTALLATION
(Refer “EXPLODED VIEW”)
CAUTION
· The Floo r jack is heavy. Use caution when
lifting out of box.
Assembly
• In the two piece handle assembly (37)
provided, assemble the upper section into
the lower section, line up the holes, insert and
tighten the screw (38). Use a 10 mm spanner /
3/8” spanner to tighten the screw.
• Insert the bottom end of handle into the top
of handle Socket (28) and securely tighten the
handle bolt (27) and washer. Ensure the handle
can turn freely. Use an 18 mm spanner / 11/16”
spanner to tighten the bolt.
• Turn the handle/release valve clockwise to the
closed position. Do not over tighten.
• Y our floo r j ack is ready for use.
OPERATING INSTRUCTIONS
(Refer “EXPLODED VIEW”)
CAUTION
• Chock vehicle’s wheels to prevent rolling while
lifting.
• Use jack stands to support vehicle. Never work
around or under a vehicle supported only by
the Floor Jack.
• Watch for movement of vehicle o r ja ck stands
as vehicle is lowered. If any movement occurs,
jack vehicle up a nd adj us t ja ck stands properly.
• When not in use, make sure pressure is
released by turning Handle Assembly fully
counterclockwise. This will prolong the life of
the jack .
Lifting
• Twist the handle assembly clockwise to close
the pressure release valve.
• Position the j ack under the speci fi ed lift point.