Eisco CH0814 Скачать руководство пользователя страница 2

ASSEMBLY & OPERATING INSTRUCTIONS

MOUNTING & PLACEMENT

This equipment can be wall mounted or bench mounted.

ENVIRONMENTAL CONDITIONS

*

For  indoor  use  only  statement:  Water  Still  is  designed  for  reliable 

continuous operation incorporating a host of features unmatched by 
comparable stills. It is Easy to Use, Portable, Safe to Operate and 
thoroughly reliable, i.e., the reason it is recommended for indoor use 
only.

*

Ambient Temperature

+5°C to 40°C

*

Altitude

:

Up to 2000 meters

*

Relative Humidity

:

Not exceeding 80%

*

Electrical Supply

:

*

:
:

*

Impairment statement :- If the equipment is not used in the manner 

may be impaired. Please read the manual carefully before installation 
or operating the unit.

Condenser

Cooling water
Inlet

Boiler

Heater

Gaskets & Clamp

Vent

Straps

Drain cock

To Drain

Constant Level
Control

Boiler Inlet

Key

Distillate 
Outlet

-1-

© EISCO SCIENTIFIC  

  www.eiscolabs.com  

:

220-240VAC, 50Hz, Single Phase

Pollution Degree

2 According to IEC 60664

*

Over Voltage Category

Category II According to IEC 60664

described in the manual the protection provided by the equipment 

IP

IP20

:

*

Содержание CH0814













Отзывы: