GB
- 8 -
5.4 Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
fi
tted in place. Vibrating wheels are to be replaced
immediately.
6. Operation
6.1 Switch (Fig. 5)
The angle grinder is secured against being swit-
ched on unintentionally.
To switch on:
First press the auxiliary button (b)
on the top side of the handle and then the main
lever of the On/O
ff
switch (2). The On/O
ff
switch
can be locked in place for continuous operation.
With the On/O
ff
switch (2) pressed, press the
auxiliary button (b) and then let go of the On/O
ff
switch.
To switch o
ff
:
Let go of the On/O
ff
switch (2); if it
was locked, press it and then let go.
Restart safeguard
If the mains power supply is interrupted (or there
is a temporary power failure for t > 0.5 s.) when
the switch is locked in the On position, the electric
tool will not run after the power supply is restored.
For the equipment to run, the switch must be tur-
ned o
ff
and then on again.
Soft start function (starting current limit)
The equipment has a soft start function for pre-
venting jerky movements when starting.
Wait until the machine has reached its top
speed. You can then position the angle grin-
der on the workpiece and machine it.
6.2 Changing the guard (Fig. 3)
•
Press the clamping lever (a) and turn the gu-
ard (4) as shown in Fig. 3.
•
Remove the guard.
•
To fit the guard, push it onto the equipment
with the clamping lever pressed as shown in
Fig. 3.
6.3 Changing the grinding wheels (Fig. 6)
Use the face spanner (5) supplied to change the
grinding wheels.
Important!
For safety reasons, the angle grinder
must not be operated with the face spanner (5)
inserted in it.
Pull out the power plug.
•
Simple wheel change by spindle lock:
•
Press the spindle lock and allow the grinding
wheel to latch in place.
•
Open the flange nut with the face spanner.
(Fig. 6)
•
Change the grinding or cutting wheel and
tighten the flange nut with the face spanner.
Important!
Only ever press the spindle lock when the
motor and grinding spindle are at a stand-
still! You must keep the spindle lock pressed
while you change the wheel!
For grinding or cutting wheels up to approx. 5 mm
thick, screw on the
fl
ange nut with the
fl
at side
facing the grinding or cutting wheel.
6.4 Flange arrangements when using grin-
ding wheels and cutting wheels (Fig.
7-10)
•
Flange arrangement when using a de-
pressed-centre or straight grinding wheel
(Fig. 8)
a) Clamping flange
b) Flange nut
•
Flange arrangement when using a de-
pressed-centre cutting wheel (Fig. 9)
a) Clamping flange
b) Flange nut
•
Flange arrangement when using a straight
cutting wheel (Fig. 10)
a) Clamping flange
b) Flange nut
6.5 Motor
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilati-
on holes clean at all times.
Anl_TP_AG_2320_SPK7_EX_KSA.indb 8
Anl_TP_AG_2320_SPK7_EX_KSA.indb 8
02.07.13 15:10
02.07.13 15:10
Содержание TP-AG 2320
