GB
- 17 -
6. Operation
6.1 Operation (Fig. 2)
•
Check that a glue stick is fitted (see point 5.2)
•
Press the On/Off switch (1) for approx. 3 se-
conds.
•
The LED (2b) will light up red to indicate that
the equipment is heating up
•
This takes approx. 15 seconds, after which
the LED (2b) changes to green
•
The equipment is now ready for operation.
•
To switch the equipment off again, press the
ON/OFF briefly just the once
Warning!
Never set the equipment down once you have
started using it.
If or when your gluing work is interrupted or
fi
ni-
shed, always be sure to stand the equipment on
its handle as shown in Fig. 1.
Switch the equipment o
ff
and allow it to cool down
completely before you pack it away.
6.2 Working with the cordless hot glue gun
•
You can now apply the glue by pressing the
trigger lever (4) after the heating up time
•
Press both surfaces together immediately
and apply pressure to them
•
It takes about 30 seconds for the glue to set.
The equipment switches o
ff
automatically after
approx. 5 minutes of non-use.
Important!
Glue stains on textiles cannot be removed.
6.3 LED indicator (Fig. 2/Item 2)
The indicator (2) displays the charging status du-
ring charging (see point 5.1), the heating time and
when the equipment is ready for operation (see
point 6.1). If the red LED (2b)
fl
ashes during ope-
ration, the battery is empty. Recharge the battery.
7. Cleaning, maintenance and
ordering of spare parts
Warning!
Allow the equipment to cool down before you start
to clean it.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
8. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council o
ffi
ces.
Anl_TC_CG_3_6_Li_SPK7.indb 17
Anl_TC_CG_3_6_Li_SPK7.indb 17
13.05.16 13:42
13.05.16 13:42
Содержание TC-CG 3,6 Li
Страница 2: ... 2 Anl_TC_CG_3_6_Li_SPK7 indb 2 Anl_TC_CG_3_6_Li_SPK7 indb 2 13 05 16 13 42 13 05 16 13 42 ...
Страница 4: ... 4 Anl_TC_CG_3_6_Li_SPK7 indb 4 Anl_TC_CG_3_6_Li_SPK7 indb 4 13 05 16 13 42 13 05 16 13 42 ...
Страница 125: ... 125 Anl_TC_CG_3_6_Li_SPK7 indb 125 Anl_TC_CG_3_6_Li_SPK7 indb 125 13 05 16 13 42 13 05 16 13 42 ...
Страница 126: ...EH 05 2016 01 Anl_TC_CG_3_6_Li_SPK7 indb 126 Anl_TC_CG_3_6_Li_SPK7 indb 126 13 05 16 13 42 13 05 16 13 42 ...