GB
- 22 -
6.4 MOTOR
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilati-
on holes clean at all times.
6.5 GRINDING WHEELS
•
Never use a grinding or cutting wheel bigger
than the specified diameter.
•
Before using a grinding or cutting wheel,
check its rated speed.
•
The wheel´s rated speed must be higher than
the idle speed of the right-angle grinder.
•
Use only grinding and cutting wheels that are
approved for a minimum speed of 8000 rpm
and a peripheral speed of 80 m/sec.
•
Check the direction of rotation when you use
diamond cutting wheels. The directional arrow
on the diamond cutting wheel must point in
the direction in which the tool rotates.
Take special care that the grinding/sanding
wheels are properly stored and transported.
Ensure that the grinding/sanding wheels are
never exposed to shock, jolts or sharp edges (for
example during transport or storage in a toolbox).
This could cause damage (such as cracks) to the
grinding/sanding wheels and place the user in
serious danger.
6.6 Swiveling the handle (Fig. 6/7)
Pull out the power plug!
The handle (2) can be swiveled a maximum 90°
to the left and right. To do so, pull the locking plate
(5) a little backwards and swivel the handle (2)
90° to the left or right.
Important:
When the locking plate (5) engages
correctly it makes an audible click.
6.7 OPERATING MODES
6.7.1 Rough grinding
Caution: Use the safety device for sanding/
grinding
(included in items supplied).
For the best rough grinding results, hold the grin-
ding wheel at an angle of between 30° and 40° to
the workpiece surface and guide back and forth
over the workpiece in steady movements.
6.7.2 Cutting
Caution: Use the safety device for abrasive
cutting
(available as accessory)
When you use the right-angle grinder for cutting
purposes, avoid tilting it in the cutting plane. The
cutting wheel must have a clean cutting edge.
A diamond cutting wheel is best used to cut hard
stone.
It is prohibited to use the machine on
asbestos materials!
Never use a cutting wheel for rough grinding.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
authorized after-sales service or similarly trained
personnel to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a quali
fi
ed electrician
and/or an authorized service agent.
Danger!
The carbon brushes should not be rep
laced by anyone but a quali
fi
ed electrician or the
authorized service technician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
Anl_TC_AG_2200.indb 22
Anl_TC_AG_2200.indb 22
16.10.2017 09:40:42
16.10.2017 09:40:42
Содержание TC-AG 2200
