GB
- 21 -
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the additional handle (Fig. 2)
•
The angle grinder must not be used without
the additional handle (3).
•
The additional handle can be secured in any
of 3 positions (A, B, C).
Tool side
Suitable for
Left (position A)
Right-handed users
Right (position B)
Left-handed users
Top (position C)
Use of cutting wheels
5.2 Setting the guard (Fig. 3)
Warning! Pull out the power plug!
•
Switch off the equipment. Pull out the power
plug.
•
Adjust the guard (7) to protect your hands
so that the material being ground is directed
away from your body.
•
The position of the guard (7) can be adjusted
to any specific working conditions. Undo the
clamp handle (a) and turn the cover (7) into
the required position.
•
Ensure that the guard (7) correctly covers
thegear wheel casing.
•
Secure the clamp handle (a) again.
•
Ensure that the guard (7) is secure.
•
To remove the guard, open the clamp handle
(a) and turn the guard far enough to be able
to remove it.
•
To fit the guard, proceed in reverse order to
removing the guard.
Take care that the safety device is secure.
Never use the angle grinder without the gu-
ard.
5.3 Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
fi
tted in place. Vibrating wheels are to be replaced
immediately.
6. Operation
6.1 Switch (Fig. 4)
To switch on:
Slide the locking button (4) to the back and press
the On/O
ff
switch (3) simultaneously.
To switch o
ff
:
Let go of the locking button and the On/O
ff
switch.
Wait until the machine has reached its top
speed. You can then position the angle grin-
der on the workpiece and machine it.
6.2 Changing the grinding wheels (Fig. 5)
Use the face spanner (8) supplied to change the
grinding wheels.
Pull out the power plug.
•
Simple wheel change by spindle lock:
•
Press the spindle lock and allow the grinding
wheel to latch in place.
•
Open the flange nut with the face spanner
(Fig. 5).
•
Change the grinding or cutting wheel and
tighten the flange nut with the face spanner.
Important!
Only ever press the spindle lock when the
motor and grinding spindle are at a stand-
still!
You must keep the spindle lock pressed while
you change the wheel!
For grinding or cutting wheels up to approx. 3 mm
thick, screw on the
fl
ange nut with the
fl
at side
facing the grinding or cutting wheel.
6.3 Flange arrangements when using grin-
ding wheels and cutting wheels
(Fig. 8-11)
•
Flange arrangement when using a depres-
sedcentre or straight grinding wheel (Fig. 9)
a)
Clamping
fl
ange
b) Flange nut
•
Flange arrangement when using a depres-
sedcentre cutting wheel (Fig. 10)
a)
Clamping
fl
ange
b) Flange nut
•
Flange arrangement when using a straight
cutting wheel (Fig. 11)
a)
Clamping
fl
ange
b) Flange nut
Anl_TC_AG_2200.indb 21
Anl_TC_AG_2200.indb 21
16.10.2017 09:40:42
16.10.2017 09:40:42
Содержание TC-AG 2200
