This will also void the warranty.
After completing steps 1 – 3, check that all the
connections are sealed correctly using leak detection
spray or soap suds. If any bubbles form, the system
has a leak and the screw connectors must be
retightened using an open-ended spanner.
4.
Bundle all the lines together to form a parcel of
lines.
Notes:
앬
Bend and position the condensation hose
carefully. (Fig. 23)
앬
Both refrigerant lines must be insulated at the
connection points.
앬
The condensation drain hose must be connected
below the refrigerant line.
앬
It must be ensured that none of the pipes on the
rear of the indoor device leak.
앬
It must be ensured that the condensation drain
hose is positioned at the lowest point of the
insulation package. The hose must be separated
from the cables and connection pipe so that no
condensation can run over the cables and pipe.
앬
Do not cross the mains cable with other cables.
앬
Please note that the power cable is not to be fed
through to the outside. All tubes, electric cables
and the drainage water hose have to be wrapped
with the supplied protective tape. Depending on
whether the lines are right-hand or left-hand
versions, the corresponding bushing
preparations must be removed from the indoor
device.
앬
The package of lines/hoses is to be laid between
the housing of the indoor device and the wall (fig.
24).
Key for Fig. 24
A = Indoor / Outdoor device connection cable
B = Refrigerant line
C = Wrapping tape
D = Condensation drain hose
5.
Guide the parcel of lines through the supplied
wall passage and through the hole in the wall
(Fig. 25/26).
6.
Attach the indoor device to the mounting plate.
The top hook (Fig. 26 / Item A) on the mounting
plate must be securely attached to the rear of the
indoor device. After you have completed the
installation work, press the indoor device into the
bottom mount (B).
C. Mounting the outdoor device
It is imperative that you follow the installation
instructions.
1. Before you start installation
앬
Select the location for installation (follow the
previous notes on selecting the location).
앬
Check that the available mains voltage is the
same as the voltage specified on the rating plate.
앬
The maximum possible distance between the
indoor and the outdoor device using the supplied
accessories is 5 m.
앬
If the outdoor device is higher than the indoor
device, make sure that a curve is made in the
coolant tube which is lower than the bottom edge
of the indoor device.
앬
Secure the condensation drain (B) to the base of
the outdoor device using the sealing disc (A).
Drain the water generated when the system is in
heating mode through a hose.
2. Installing the outdoor device
앬
The outdoor device can be fastened to the
ground or to a wall bracket (e.g. special
accessory Art. No. 23.651.57) with dowels and
screws. To do so, use the holes on the device.
3. Connecting the refrigerant line to the outdoor
device
Important.
Refer to section 5.1 which contains the main
instructions for connecting the refrigerant lines.
Notes:
1. Have all service work performed by a specialist
firm only. Request a copy of our list of service
partners for any such work.
2. If ever the voltage carrying cable between the
indoor device and the outdoor device should be
damaged, contact a specialist firm.
3. If the power cable should ever be damaged,
have it replaced by an electrician.
4. Important
note:
a) The maximum length of the coolant line in the
basic version is 5 meters.
b) If the outdoor device is higher than the indoor
device, a curve will be required in the coolant
tube which is positioned below the height of the
indoor device.
1.
Fig. 28:
Remove the connection cover on the
outdoor equipment.
2.
Fig. 29:
Do not remove the plastic seals from the
outdoor equipment and the appropriate
GB
23
Anleitung_Split_2500-3500_EQ_C_H_GB:_ 10.12.2008 11:54 Uhr Seite 23
Содержание Split 2500 EQ C+H
