EINHELL RT-TS 1825 U, Оригинальная инструкция по эксплуатации, Страница: 16 / 80

connection with the machineʼs construction and
design:
n
Contact with the saw blade in the uncovered
saw zone.
n
Reaching into the running saw blade (cut
injuries).
n
Kick-back of workpieces and parts of work-
pieces.
n
Saw blade fracturing.
n
Catapulting of faulty carbide tips from the saw
blade.
n
Damage to hearing if ear-muffs are not used as
necessary.
n
Harmful emissions of wood dust when used in
closed rooms.
5. Technical data
AC motor 230V - 240V
쓒
50Hz
Power P S1 1500 W S6 40% 1800 W
Idle speed n
0
5700 min -1
Cutting-off wheel Ø 250 x Ø 30 x 2.4 mm
Number of teeth 24
Table size 625 x 440 mm
Table width extension, left/right 625 x 250 mm
Table length extension, rear 400 x 440 mm
Cutting height max. 73 mm/90°
53 mm / 45°
Height adjustment infinite 0 -73 mm
Tilting saw blade infinite 0° - 45°
Extractor socket Ø 36 mm
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Idle mode
Sound pressure level LPA 104,5 dB(A) 95,5 dB(A)
K
pA
uncertainty 3 dB
Sound power level LWA 114,1 dB(A) 105,2 dB(A)
K
WA
uncertainty 3 dB
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.
Wear ear-muffs.
The impact of noise can cause damage to hearing.
„ Keep the noise emissions and vibrations to a
minimum.
n
Only use appliances which are in perfect working
order.
n
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
necessary.
n
Switch the appliance off when it is not in use.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment’s
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
6. Before putting the machine into
operation
n
Unpack the bench-type circular saw and check it
for damage which may have occurred in transit.
n
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
n
All covers and safety devices have to be
properly fitted before the machine is switched
on.
n
It must be possible for the saw blade to run
freely.
n
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
n
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
n
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
GB
16
Anleitung_RT_TS_1825_U_SPK1_- 26.09.13 15:40 Seite 16