GB
- 27 -
7.3 Preparing the mower for long-term
storage
Warning!
Do not empty the petrol tank in enc-
losed areas, near
fi
re or when smoking. Petrol
fumes can cause explosions and
fi
re.
1. Drain the petrol tank using a petrol extraction
pump.
2. Start the engine and run it until the tank and
fuel line are completely empty and the engine
stalls.
3. Change the oil after each season.
4. Remove the spark plug. Use an oil-can to
fi
ll
the cylinder with approx. 20 ml of oil. Slowly
pull back the starter handle, which will bathe
the cylinder wall with oil. Screw the spark plug
back in.
5. Clean the cooling
fi
ns of the cylinder and the
housing.
6. Be sure to clean the entire equipment to pro-
tect the paint.
7. Store the equipment in a well-ventilated
place.
7.4 Preparing the mower for transport
Warning!
Do not empty the petrol tank in enc-
losed areas, near
fi
re or when smoking. Petrol
fumes can cause explosions and
fi
re.
1. Drain the petrol tank using a petrol extraction
pump.
2. Always let the engine run until it has used up
the remainder of petrol in the tank.
3. Empty the engine oil from the warm engine.
4. Remove the spark plug connector from the
spark plug.
5. Clean the cooling
fi
ns of the cylinder and the
housing.
6. Unhook the starter cable from the hook (Fig.
3c). Slacken the connection shown in Fig. 3b
on the left and right of the push bar and swing
down the upper push bar. Make sure that the
actuator cables do not get kinked when the
bar is pulled up.
7. Wedge a few layers of corrugated cardboard
between the upper and lower push bars and
the engine in order to prevent any cha
fi
ng.
8. Secure the load su
ffi
ciently so that it cannot
slip and cause damage or injuries during
transportation.
7.5 Consumables, wear materials and spare
parts
Spare parts, consumables and wear materials
such as engine oil, V-belts, spark plugs, air
fi
lter
inserts, petrol
fi
lters, batteries and blades are not
covered by the warranty.
7.6 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
8. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council o
ffi
ces.
Anl_GC_PM_40_SPK9.indb 27
Anl_GC_PM_40_SPK9.indb 27
18.10.2018 13:54:14
18.10.2018 13:54:14
Содержание GC-PM 40
Страница 144: ... 144 Anl_GC_PM_40_SPK9 indb 144 Anl_GC_PM_40_SPK9 indb 144 18 10 2018 13 54 28 18 10 2018 13 54 28 ...
Страница 145: ... 145 Anl_GC_PM_40_SPK9 indb 145 Anl_GC_PM_40_SPK9 indb 145 18 10 2018 13 54 28 18 10 2018 13 54 28 ...
Страница 146: ...EH 10 2018 01 Anl_GC_PM_40_SPK9 indb 146 Anl_GC_PM_40_SPK9 indb 146 18 10 2018 13 54 28 18 10 2018 13 54 28 ...