GB
- 27 -
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before
starting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment.
Ensure that no water can seep into the
device. The ingress of water into an electric
tool increases the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a quali
fi
ed electrician.
Danger!
The carbon brushes should not be re-
placed by anyone but a quali
fi
ed electrician, or
the autorized service technician.
8.3 Maintenance
•
Worn out or damaged blades, blade mounts,
and bolts should be replaced as a set by an
authorized professional in order to keep the
equipment in balance.
•
Do not clean the lawn mower with running
water, particularly with high-pressure water.
Ensure that all mounting components (i.e.
screws, bolts, nuts etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Frequently check the grass catch assembly
for signs of wear.
•
Replace excessively worn or damaged parts
immediately.
•
Store your lawn mower in a dry room.
•
In order to ensure that you enjoy the
equipment for many years to come, all
screwed parts, as well as the wheels and
axles, should be cleaned and lubricated.
•
Keeping your lawn mower in good condition
not only ensures a long lifespan and high
performance, but also enables the equipment
to thoroughly cut your grass with minimal
effort. For best results, clean the lawn mower
with a brush or rag. Do not use any solvents
or water to remove dirt.
•
The blade is subjected to more wear and
tear than any other component. Therefore,
routinely check the condition of the blade
and make sure that it is tightly fastened. If
the blade is completely worn out, it must be
immediately replaced or ground sharp again.
An excessively vibrating mower means that
the blade is not properly balanced or has
become deformed from striking an object.
In this case, the blade must be repaired or
replaced.
•
There are no parts inside the equipment
which require additional maintenance.
8.4 Replacing the blade
For safety reasons, we recommend having the
blade replaced by an authorized professional. Im-
portant! Wear work gloves! Only replace the blade
with a genuine Einhell replacement blade, as this
will ensure top performance and safety under all
conditions.
Carry out the following steps to change the blade:
1. Undo the fastening screw (see Fig. 11a).
2. Remove the blade and replace with a new
one.
3. When
fi
tting the blade, make sure it is ins-
talled in the right direction. The blade‘s air va-
nes must project into the motor compartment
(see Fig. 11b). The dome mounts must be
aligned with the punch holes in the blade.
4. Then retighten the fastening screw with the
universal wrench. The tightening torque
should be approx. 25 Nm.
At the end of the season, perform a general ins-
pection of the lawn mower and remove any grass
and dirt which may have accumulated. At the start
of each season, ensure that you check the condi-
tion of the blade. If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.
8.5 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
Spare blade art. no.: 34.054.30
Anl_SA_GC_EM_1536.indb 27
Anl_SA_GC_EM_1536.indb 27
05.07.2018 08:37:28
05.07.2018 08:37:28