EINHELL BT-GW 150, Оригинальная инструкция по эксплуатации, Страница: 22 / 112

22
GB
Inserting the wire spool (Fig. 28, 29)
Place the wire spool (N) on the spool holder (B).
Ensure that the end of the welding wire is unwound on
the side of the wire guide, see arrow.
Ensure that the spool lock (A) is pushed in and the
cam pin (C) is engaged in the cam opening in the wire
spool (O). The spool lock (A) must engage again over
the wire spool (N). (Fig. 27)
Inserting the welding wire and adjusting the wire
guide (Fig. 30-36)
Push the pressure roller spring (K) upwards and
swing it forwards (Fig. 30).
Pull the pressure roller holder (J) with the
pressure roller (I) and pressure roller spring (K)
downwards (Fig. 31).
Undo the screws for the feed roller holder (E) and
pull off the feed roller holder (F) upwards (Fig.
32).
Check the feed roller (G). The appropriate wire
thickness must be specified on the top of the feed
roller (G). The feed roller (G) is fitted with two
guide grooves. Turn the feed roller (G) over if
necessary or replace it. (Fig. 33)
Position the feed roller holder (F) again and
secure it.
Remove the gas nozzle (Fig. 5/12) from the
burner (Fig. 5/13) by turning it clockwise, unscrew
the contact tube (Fig. 6/26). (Fig. 5 – 6). Place the
hose package (Fig. 1/11) on the floor as straight
as possible pointing away from the welding set.
Cut off the first 10 cm of the welding wire to
produce a straight cut with no shoulders, warping
or dirt. Deburr the end of the welding wire.
Push the welding wire through the guide tube (M)
between the pressure and feed rollers (G/I) into
the hose package mounting (H). (Fig. 34)
Carefully push the welding wire by hand into the
hose package until it projects out of the hose
package by approx. 1 cm at the burner (Fig. 5/13).
Undo the adjusting screw for counter-pressure (L)
a few turns. (Fig. 36)
Push the pressure roller holder (J) with pressure
roller (I) and pressure roller spring (K) upwards
again and attach the pressure roller spring (K) to
the adjusting screw for counter-pressure (L) again
(Fig. 35).
Now set the adjusting screw for counter-pressure
(L) so that the welding wire is positioned firmly
between the pressure roller (I) and feed roller (G)
without being crushed. (Fig. 36)
Screw the appropriate contact tube (Fig. 6/26) for
the welding wire diameter on to the burner (Fig.
5/13) and fit the gas nozzle, turning it clockwise
(Fig. 5/12).
Set the adjusting screw for the roller brake (D) so
that the wire can still be moved and the roller
stops automatically after the wire guide has been
braked.
6. Operation
6.1 Setting
Since the welding set must be set to suit the specific
application, we recommend that the settings be made
on the basis of a test weld.
6.1.1 Setting the welding current
The welding current can be set to 6 different levels
using the ON/OFF/Welding current switch (Fig. 1/7).
The required welding current depends on the material
thickness, the required penetration depth and the
welding wire diameter.
6.1.2 Setting the wire feed speed
The wire feed speed is automatically adjusted to the
current setting. The final wire feed speed setting can
be made on the welding wire speed controller (Fig.
1/14). We recommend that you start the setting work
at level 5 which is the middle value, and then adjust it
from there. The required quantity of wire depends on
the material thickness, the penetration depth, the
welding wire diameter and also of the size of the gap
to be bridged between the workpieces you wish to
weld.
6.1.3 Setting the gas delivery rate
The gas delivery rate can be infinitely adjusted on the
pressure reducer (Fig. 4/19). It is shown on the
pressure gage (Fig. 4/20) in liters per minute (l/min).
Recommended gas delivery rate in rooms with no
drafts: 5 – 15 l/min.
To set the gas flow rate, first release the clamp lever
(Fig. 28/G) on the wire feed unit to prevent
unnecessary wire wear (Fig. 5.4.3). Connect to the
mains outlet (see point 5.3), set the ON/OFF/Welding
current switch (Fig. 1/7) to setting 1 and press the
burner switch (Fig. 5/25) to start the gas flow. Now set
the required gas delivery rate on the pressure reducer
(Fig. 4/19).
Turn the rotary knob (Fig. 4/24) counter-clockwise:
Lower gas delivery rate
Turn the rotary knob (Fig. 4/24) clockwise:
Higher gas delivery rate
Secure the clamp lever (Fig. 28/G) to the wire feed
unit again.
Anleitung_BT_GW_150_SPK1__ 23.01.13 07:26 Seite 22