EINHELL BG-CT 18/1 Li, Оригинальная инструкция по эксплуатации

Страница: 18 / 40

GB
- 18 -
If the battery pack still fails to charge, send
•
the battery charger with charging adapter
•
and the battery pack
•
to our customer services department.
To ensure that the battery pack provides long ser-
vice you should take care to recharge it promptly.
Recharging is always necessary when you notice
a drop in the performance of your cordless grass
trimmer. Never fully discharge the battery pack.
This will cause it to develop a defect.
6. Operation
Your grass trimmer will work at its best if you ob-
serve the following instructions:
•
Never use the grass trimmer without its safety
devices.
•
Do not cut grass when it is wet. The best re-
sults are had on dry grass.
•
To switch on your grass trimmer, press the sa-
fety lock-off and the ON/OFF switch (Fig. 2/
Pos. 2).
•
To switch off your grass trimmer, let go of the
ON/OFF switch (Fig. 2/Pos. 2).
•
Do not move the grass trimmer against the
grass until the switch is pressed, i.e. wait until
the trimmer is running.
•
For the correct cutting action, swing the grass
trimmer to the side as you walk forward, hol-
ding it at an angle of approx. 30° as you do so
(see Figure 14+15).
•
Make several passes to cut long grass shor-
ter step by step from the top (see Figure 16).
•
Use the guard hood to prevent unnecessary
wear.
•
To avoid unnecessary wear, keep the grass
trimmer away from hard objects.
Using the grass trimmer as an edge trimmer.
The grass trimmer can be adjusted as follows to
trim the edges of lawns and fl ower beds.
•
Remove the battery (Fig. 10)
•
Pull the adjusting sleeve (Fig. 7 / Item C) in
the direction shown in Fig. 7.
•
Hold the adjusting sleeve in the drawn-back
position and turn the lower part of the trimmer
through 180° until it latches home.
•
Now you have converted the grass trimmer to
an edge trimmer for cutting the lawn vertically.
7. Cleaning, maintenance and
ordering of spare parts
Before putting away or cleaning the grass trim-
mer, pull out the battery pack (Fig. 10).
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment. En-
sure that no water can seep
into the device.
•
Remove deposits from the guard hood with a
brush.
7.2 Replacing the blade (Fig. 12-13)
IMPORTANT! Make sure that you remove the
battery pack before replacing the blade (Fig.
10).
•
Use the supplied assembly tool to fit and re-
move the blade (Fig. 12/Item 12).
•
To remove the blade, push the blade inwards
and remove via the larger opening as shown
in Figure 12.
•
To fit the new blade, proceed in reverse order.
Make sure the blade locks into place correctly
as shown in Figure 13.
7.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Spare blade art. no.: 34.057.30
Anleitung_BG_CT_18_1_Li_SPK7.indb 18 Anleitung_BG_CT_18_1_Li_SPK7.indb 18 03.05.12 11:05 03.05.12 11:05